A bottle that will not hold a cap, or weeps at the neck after capping, usually comes back as a complaint about the filling line. The neck is where that complaint starts. It is the thickest section of the container, formed over the blow pin and cooled by the neck insert, and it must stay round while the body shrinks. When it comes out oval the cost is more than scrap: caps jam in the sorter, capping torque drifts, and the leak rate moves with the weather on the plant floor.
Measure the neck before you change a setting
Neck ovality is the largest neck outside diameter minus the smallest, both measured at the same height at four points around the circumference. Measure it first, compare with the closure drawing, then pick a cause. The usual order is uneven neck cooling, an off-centre blow pin and a worn neck insert.
The neck is not a small version of the body. It carries the thread, the bead and the sealing land, and those features must match a cap molded elsewhere to another molder's tolerance. A body panel slightly out of shape is invisible; a neck slightly out of round can leak. That is why it needs its own sheet, not a glance at the take-off conveyor.
The four-point sheet and the ovality number
Write the method on the sheet, not only the result. Two people measuring the same bottle at different heights, or with different anvil shapes, will report different ovality and then argue about the machine for a week.
- Stand the bottle upright, mark 0°, 90°, 180° and 270° on the neck, and measure at the same height each time, normally below the thread.
- Use a micrometer or a flat-anvil caliper. A sharp-anvil caliper on a curved neck reads low and gives a false ovality number.
- Record all four readings in the same unit, then take ovality as maximum minus minimum. Keep the raw readings; one figure hides which side is flat.
- Measure five bottles per cavity at the start, middle and end of the run. One oval neck can be a handling mark; a trend points to cooling or insert wear.
No universal ovality limit is worth publishing. A deep thread with a soft liner tolerates more out-of-round than a flat sealing land with a hard liner. Ask the closure supplier for the roundness limit that matches the cap you buy, put that number on the sheet, and write the measuring height and instrument beside it. Change the closure and the limit means nothing until the sheet is updated.
| Check | How to record it | Decision rule |
|---|---|---|
| Neck OD at 0°, 90°, 180°, 270° | Micrometer or flat-anvil caliper at the same height | All four readings inside the closure drawing band |
| Ovality | Maximum OD minus minimum OD at that height | Against the closure supplier's roundness limit |
| Thread and bead profile | Profile gauge or a thread section | Matches the closure drawing |
| Cap fit | Production cap, seat by hand, check removal torque | No rocking, torque inside the agreed band |
| Leak | Air-decay or water test at the agreed pressure and time | No drop or bubble at that condition |
Swipe the table to see all columns →
Causes in shop order
The list is ordered by how often the cause appears on a running machine, not by how easy it is to adjust. Work down it and stop when the four-point readings come back inside the closure limit.
- Neck cooling. The insert holds the neck round while the parison is still soft. A scaled channel, low water flow or poor insert contact leaves one side warm, and that side shrinks after demolding. Check flow at the return line.
- Blow-pin centering. A pin that sits off-centre pushes the parison to one side before the mold closes, so the neck ends up thick on one side and thin on the other. Check the pin with a dial indicator.
- Neck insert wear. A bell-mouthed entry, a scratched sealing face or a worn thread will not hold the neck shape. Pull the insert, measure the critical diameters and compare with the drawing rather than judging by eye.
- Demolding temperature. A neck released while still soft deforms on the take-off arm or in the chute, and the ovality shows up at the gauge minutes later. Measure neck surface temperature at take-off, not body temperature.
- Parison fold at the neck. A parison that is off-centre, too cold or too long folds instead of expanding evenly, and the fold line becomes the flat side of the oval. A visible fold in the neck section is a parison problem, not a cooling problem.
Neck behaviour also depends on how the machine holds the pin. Thesingle-station 0–16 L rangeand thedouble-station 0–16 L rangeuse different clamp and take-off layouts. If ovality appears only on the first shift after a stop, readstartup and shutdownbefore adjusting the tool.
Cap fit and leak test: the two checks that decide
A neck can pass the four-point check and still leak, because the thread is shallow on one side or the sealing land is not square. Close the loop with a cap-fit check and a leak test at the condition agreed with the customer, and record the cavity number with every result. A leak on one cavity only points at that station's insert.
Material changes the neck behaviour but not the method. HDPE is stiffer at demolding and shrinks more as it cools, so a neck that is round at take-off can move later. PETG runs hotter and depends on mold temperature for clarity, so neck and body circuits must be balanced, not set the same. Judge each material against its own closure drawing.
What to send for a quotation
Neck ovality work usually ends in a machine, a mold or a neck insert, so a quotation needs the numbers you used to measure the problem. Send these with the inquiry.
- Container drawing with the neck finish, thread standard and sealing land, plus the closure drawing or a cap sample.
- Material, color and regrind percentage, because all three change shrinkage and neck stiffness.
- Cavity count, target output per hour and the measured cycle time you work to.
- Four-point neck readings from good and bad bottles, with height, instrument and the limit you measure against.
- Current machine model or the container range you plan to run, plus plant voltage and air supply.
If the container is still at the drawing stage, send it through thecontact pageand mark the neck finish as the critical dimension.
Source: E-SHION product data. Specifications are subject to change without notice; customization is available.
This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.