A new mold goes in, the first bottles look acceptable, and a week later the buyer sends photos: dull patches near the neck, a base that no longer sits flat, and a height that has drifted out of tolerance. In most of these arguments the melt temperature has been checked twice and the mold temperature was never measured.

The short answer: material first, then the mold

Treat mold temperature as a starting window, not a fixed number. HDPE generally runs a cool mold, PP a little warmer for surface and seam strength, and PETG in a narrow band where clarity holds. Grade, wall thickness, mold steel and cooling layout move the final setpoint, so confirm it on a measured trial.

Why mold temperature is a cooling decision

The number on the chiller is not the number the plastic sees. What the parison touches is the cavity surface, and that surface decides how fast the skin freezes, how well the mold finish is copied, and how much stress is locked into the wall. A warmer mold slows that freeze: gloss and seam strength usually improve, but the cycle lengthens, shrinkage grows and a deep core may drag. A colder mold speeds the cycle and steadies dimensions, until the surface turns dull or the pinch-off weakens. Adjust it with cycle time and wall thickness, never on its own.

  • Surface gloss and how faithfully the cavity texture is copied
  • Pinch-off and base seam strength, which depend on the plastic welding while it is still hot
  • Frozen-in stress, which later appears as stress cracking, ovality or a base that creeps
  • Cycle time, because the part must be stiff enough to eject without marking
  • Shrinkage and warpage measured hours after the part leaves the mold

Starting windows for HDPE, PP and PETG

Common starting windows for mold cooling water in extrusion blow molding are below. They are a test plan, not a specification: a 20 L jerrycan and a 200 ml bottle in the same material do not run at the same setpoint, and a mold with poor circuit balance will read differently at each cavity. Confirm against the resin datasheet, then adjust on the machine.

Mold temperature starting windows by material, given as cavity surface readings. Confirm against the resin datasheet and mold drawing before production.
Material Starting window Warmer mold buys Warmer mold costs Check first
HDPE10–25 °CGloss on textured cavities, easier release from deep coresLonger cycle, more shrinkage and warpage on large flat panelsPinch-off and base seam at the cold end
PP20–40 °CGloss, seam strength, less stress whiteningSticking on deep draws, longer cycle, more shrinkageEven cooling across the cavity; PP warps easily
PETG15–30 °CClarity, fewer chill marksSticking, ejection marks, longer cycleHaze or chill marks at corners; polish and circuit balance

Swipe the table to see all columns →

Read the window as water temperature at the mold inlet, then subtract what the circuit loses. A mold with scaled channels, long hoses or a single pass through a hot half can sit well above the chiller setting. If the return water is much warmer than the supply, fix flow before you touch the setpoint.

5L Plastic Bottle Blow Molding Machine | Mold and Take-Off A representative 5l plastic bottle blow molding machine | mold and take-off clip. The machine, mold and configuration in your project may differ.

Where to point the infrared thermometer

An infrared thermometer is only useful if the reading is repeatable. Shiny aluminum and stainless cavities have low emissivity and read low; a matt paint dot or a contact probe can correct this. Measure at the same moment in every cycle, immediately after the mold opens, before the part is taken out.

  • Neck ring or thread area, the thin section that sets first
  • Mid-body at a marked height, on the cavity wall rather than the core
  • Base centre and base corner, where the section is thickest
  • Supply and return water pipes, as a cross-check on the meter
  • Ambient temperature beside the machine, once per shift

The mold is stable when three consecutive shots read the same at the same points and the return water stops climbing. On a heavy mold this can take longer than the machine warm-up. Do not start a comparison trial earlier, or the first parts will be colder and the data will lie.

A trial record that settles the gloss and shrinkage argument

When a buyer says the surface is dull and the molder says the mold is fine, a record settles it, not an opinion. Keep parison, blow pressure and cycle fixed, change only the mold water in small steps, and label every part by cavity and shot. E-SHION trial records put mold temperature, melt temperature and cycle time on one sheet, so a change in gloss or shrinkage traces to a single variable.

  • Shot number, cavity number and time of day
  • Melt temperature at the head and blow pressure
  • Supply and return mold water temperature, plus flow
  • Infrared cavity readings at neck, body and base
  • Part weight and wall thickness at four marked points
  • Gloss against a reference photo, and 24-hour shrinkage on two dimensions

If the trial shows the cycle is the limit rather than the mold, readblow molding process parameters, thenjerrycan mold design. For 5–10 L work the machine side is covered undersingle-station 0–16 L.

What to send for a quotation

A machine quotation is only as good as the container data behind it. Mold temperature is part of that picture because it sets cooling time, and cooling time sets the cycle. Send the following and the reply can include a realistic output estimate rather than a range.

  • Container drawing with volume, neck finish, target weight and wall thickness
  • Resin grade and datasheet, including regrind percentage if you use it
  • Cavity count, mold drawing and whether the mold already exists
  • Current cycle time, melt temperature and mold water temperature, if a machine is running
  • Target output per hour and shift pattern
  • Destination country and power supply

Photos of the current part and a rejected sample are often more useful than a paragraph of description, especially for surface and shrinkage complaints.

Send the files through thecontact pageor WhatsApp; drawings can be marked up and returned with the quotation.

Source: E-SHION product data. Specifications are subject to change without notice; customization is available.

This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.