A container can fail on material choice before the machine is sized. HDPE gives toughness and chemical resistance but an opaque wall. PETG gives clarity but adds drying, mold polish and temperature control. PVC narrows the process window. Resin sets shrinkage, wall weight and machine configuration; change it after the mold is cut and the saving turns into a new mold and another trial.

The short answer: choose by the container's job

Start with what the container must survive, not the resin price. Opaque chemical or industrial containers that must take impact start with HDPE. Stiffness or heat resistance starts with PP. Clear cosmetic jars and bottles start with PETG. Clear, chemical-resistant containers can be evaluated in PVC if the process window can be controlled. Each family has many grades; confirm grade and shrinkage on the mold.

The platform comes next: the 0.1–16 L single-station series covers bottles up to 16 L, the 20–50 L series larger containers, and this sizing guide sets the order.

Compare the four materials

The table compares the four families on what changes the mold, machine, trial plan and project cost. Shrinkage, service temperature and chemical compatibility come from the resin data sheet, not the family name.

HDPE, PP, PETG and PVC compared for extrusion blow molded containers
Material Strength and appearance Chemical and heat note Mold and process note Typical container Cost driver
HDPETough, opaqueChemical resistance; confirm the grade against the contentsWall map and regrind set on trialJerrycans, drums, oil canistersGrade, wall weight, regrind
PPStiff, translucentHeat and stiffness; confirm compatibilityAllow shrinkage and cooling; check warpageStiff or heat-resistant containersWall weight, cooling, shrinkage allowance
PETGClear, cosmeticClarity; confirm chemical exposureDry resin; polish, mold temperature, coolingClear cosmetic jars and bottlesDrying, polish, temperature control
PVCClear, chemical-resistantClarity and chemical resistance; narrow windowControl temperature and residence timeClear chemical-resistant containersProcess control, trial time

Swipe the table to see all columns →

Treat the table as questions for suppliers, not a ranking. A clear material can add drying or mold-finish cost; a tough one can still miss the shelf look. The right choice meets the acceptance criteria at the lowest total cost.

Match material to container and machine

For jerrycans, chemical drums and oil canisters, HDPE is the default: tough, opaque, chosen for chemical resistance. PP suits containers where stiffness or heat resistance matters more than clarity; the translucent look is a design choice, not a defect. Agree grade and wall map before the mold is cut.

Clear jars and bottles in this range go to PETG, where drying, melt and mold temperature, cooling and polish form one chain. PVC can also make clear, chemical-resistant containers, but its process window is narrower; the trial must watch temperature, residence time, screw and die.

For the PET versus PETG decision, see PET vs PETG blow molding.

Material sizes the machine. Clamp follows mold projection area and blowing pressure, not litres alone. The ES-10LS has 110 kN clamp, a 70–75 mm screw and 80–100 kg/h output; the ES-30L has 215 kN and 80 mm. Material availability is confirmed per configuration.

Where material choice hits cost

Material choice reaches the budget through machine, mold, auxiliaries and resin per part. As a market frame, not an E-SHION quote, 1–5 L machines commonly sit around USD 25,000–70,000; 5–30 L USD 40,000–90,000; 30–50 L USD 60,000–120,000. PETG clear-bottle machines sit around USD 60,000–120,000, with polishing and temperature control adding cost. Blow molds are roughly USD 2,000–5,000 for a simple two-cavity mold and USD 15,000–35,000 for larger multi-cavity tools, commonly 20–60 days after drawing approval. Auxiliaries are quoted separately.

Resin cost per part is shot weight times grade price, plus scrap and machine-time share. A clear material brings mold-finish and drying cost; wall weight and regrind behavior differ by material. Compare total project cost, not machine price; confirm the final figure in the quotation.

Prove it on the actual mold

A data sheet describes pellets, not a container. Run production resin and final mold together, then check wall thickness at fixed points on every cavity, neck fit and appearance under the agreed light. Record grade, lot, drying, temperature, mold temperature and cooling as the baseline; plan output from measured cycle time, not another material's estimate. A single-cavity defect usually points to that die, neck insert or cooling.

PETG Clear Bottle Blow Molding Machine | Parison and Mold View Representative PETG clear-container clip showing the parison and open mold. Your material, machine, mold and configuration may differ; use the clip to see the sequence, not as a performance claim.

What to send for a quotation

A material quotation needs the container and its service described. Send the drawing or 3D file with capacity, neck and wall range; state contents and storage conditions, including concentration and temperature; set the clarity target with a reference sample; name the grade if fixed, or ask for a shortlist.

  • Drawing or 3D file with capacity, neck and wall range.
  • Contents and storage conditions, including concentration and temperature.
  • Clarity and colour target with an accept/reject sample.
  • Resin grade, or the properties required.
  • Target output, cavity count and shift pattern.
  • Destination, voltage and utilities.

Send the drawing through the contact page and say whether an existing mold or take-out must be reused.

E-SHION can then confirm the platform, propose the mold and trial plan, and separate machine, mold and auxiliaries. Material availability is confirmed per series and configuration; do not assume every series runs every material.

Source: E-SHION product data. Specifications are subject to change without notice; customization is available.

This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.