A wide-mouth jar looks easier than a bottle: no narrow neck to blow into, no long parison to center. Buyers budget it that way, then samples come back with an oval rim, a thin shoulder or a lid that leaks. The opening, shoulder and sealing surface decide the margin — before the machine is ordered.
The short answer: size the mold, not the litre
A wide-mouth jar is a mold decision before a volume decision. A 3 L jar can have a wider body and a larger mold outline than a 5 L bottle, so the model that matches the litres may not fit. Start with the drawing: outline, projection area, cavity spacing, neck insert and trim position.
On the 0–16 L single-station platform, start with the ES-2LS up to 2 L, the ES-5LS for 2–5 L, the ES-10LS for 5–10 L and the ES-16LS near 16 L or for a tall, heavy mold. Published clamps are 100, 100, 110 and 155 kN respectively; platens run from 290 × 320 to 500 × 490 mm. These are starting points, not approvals.
Three checks decide:
- The mold outline and weight fit the platen and clamping area.
- Projection area × blowing pressure stays inside the clamp with a margin.
- The neck insert, trim station and take-out clear the mold and frame.
All three pass: the smaller model is the better buy. One fails: the next model up is cheaper than a mold that does not fit.
The cavity and take-out logic for small jars is in 1 L and 2 L bottle production; materials are compared in blow molding material selection. Machine data is on the 0–16 L single-station page.
The opening is formed, then cut
The neck is formed in the blow mold and finished after take-out. A wide-mouth jar is usually trimmed or reamed, and that cut creates the sealing surface. Trim is a process step: a dull blade, a jar cut too hot or a loose fixture leaves a wavy or sloped rim.
Measure the rim before blaming the machine: opening roundness, sealing-surface flatness and wall thickness below the neck. Ovality can come from uneven cooling around a thick neck ring, an off-center blow pin, mold close on a cold parison or ejection before the jar is stable. The fixes are in the mold, cooling circuits and trim fixture.
Shoulder and wall: where the parison thins
A wide opening forces the parison to expand sideways in a short distance. The shoulder often thins first, while the bottom runs thick because it is not stretched the same way. The die-gap profile and parison programmer should place material where the stretch is greatest; a wall map proves what the mold received.
Cut jars at several heights and around the circumference, measure the same points on every cavity, and keep the sections with the trial record. The thinnest point that must hold stacking or internal pressure sets the wall specification. A thick neck ring and a thin body cool at different rates, so use separate cooling circuits and a temperature survey.
| Jar size | First model to price | Clamp / platen | Extruder output | What decides the step-up |
|---|---|---|---|---|
| Up to 2 L | ES-2LS | 100 kN / 290 × 320 mm | 50–55 kg/h | Mold outline and trim; a short, wide body can need the ES-5LS platen |
| 2–5 L | ES-5LS | 100 kN / 320 × 380 mm | 65–80 kg/h | Projection area and cavity spacing; check clamp margin |
| 5–10 L | ES-10LS | 110 kN / 450 × 480 mm | 80–100 kg/h | Mold weight and take-out; a wide body can need the ES-16LS platen |
| 10–16 L | ES-16LS | 155 kN / 500 × 490 mm | 100–120 kg/h | Mold height, weight and clamp; confirm on the drawing |
Swipe the table to see all columns →
Output arithmetic and the cooling limit
Output = cavities × good parts per cavity per cycle × cycles per hour; cycles per hour = 3,600 ÷ measured cycle time in seconds. As a capacity check, a 10 L jar at 180 g and an extruder output of 90 kg/h — inside the ES-10LS 80–100 kg/h range — gives 90 ÷ 0.180 = about 500 jars per hour of melt, before flash and rejects. That shows whether the extruder can feed the cavities, not a cycle time.
Cooling is the other limit. The heavy rim and large opening must be cool enough to trim and hold shape. Pushing the cycle before the rim is stable only moves the problem to the trim station and the leak test.
The clip shows a wide-mouth container in the open mold and the finished part at the end of the cycle. Use it to check the mold and part shape, not cycle time.
Extrusion blow molding or injection blow molding?
A wide mouth is a standard job for extrusion blow molding: one blow mold, an integral shape, and the neck finished after take-out. Injection blow molding injects a parison on a core rod, so the thread and bore start with tighter control; the price is a preform mold plus a blow mold.
Decide by two things: whether the neck is what your filling line checks first, and whether annual volume can carry two matched tools. Large jars, integral handles and multi-layer walls usually favor extrusion blow molding on tooling cost. For a small jar with a critical thread and enough volume, get an injection-blow quote on the same drawing. E-SHION's published range covers 0.1–50 L extrusion blow molding; if the trimmed neck cannot hold the drawing, say so early.
- Neck tolerance: can the trimmed sealing surface hold the drawing, and who measures it?
- Volume: does the order keep a preform mold and a blow mold busy?
- Tooling: one blow mold against a matched set — compare the set.
A normal sealing surface rarely needs the extra tool set. If the closure leaks unless the thread is injected, get both quotes on the same drawing and annual volume.
Cost and what to send for a quotation
Market ranges, not E-SHION prices: 1–5 L machines are commonly quoted at roughly USD 25,000–70,000, and 5–30 L machines at USD 40,000–90,000. A simple two-cavity blow mold is roughly USD 2,000–5,000; a larger multi-cavity tool USD 15,000–35,000, with 20–60 days commonly needed after drawing approval. A wide-mouth mold adds a neck insert, trim detail and sealing-surface requirement, so compare the mold scope line by line. Chiller, compressor, grinder and conveyor are separate. Final price depends on model, mold, cavity layout, material, drive/control and destination — confirm it in the quotation.
Send these with the inquiry:
- Jar drawing or 3D: body diameter, height, opening and neck finish, thread or snap detail, sealing surface and wall-thickness map.
- Closure drawing or sample, including liner; fill product and temperature if they affect material choice.
- Material and grade (HDPE, PP, PETG, PVC and so on), colour, regrind policy and clarity requirement.
- Target output per hour or shift, cavity preference, shifts per day, finished goods or gross output.
- Existing mold data: outline, cavity spacing, neck insert, trim and take-out; site power, cooling water, air and floor loading.
- Destination, voltage and frequency, installation and training, downstream leak test, labelling and packing.
A wide-mouth quotation is comparable only when mold scope, trim method and cavity layout are on the table. Send the drawing and closure together; the rim decides the project.
Process comparison: extrusion vs injection blow molding; wall measurement: blow molding wall thickness control. Send the drawing through the contact page.
Source: E-SHION product data. Specifications are subject to change without notice; customization is available.
This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.