A used blow molding machine is priced on what the seller thinks it is worth, not on what it will cost you to run. Two machines of the same model and year can differ by a screw, a hydraulic pump and a year of hard production. The inspection below is the one to run before money leaves your account, ordered so that the expensive problems surface first.

The short answer: prove the machine, not the listing

Run ten checks before you pay: clamp parallelism and platen wear, screw and barrel, die head and mandrel, hydraulic pump and oil temperature, heating zones and thermocouples, control system and spares, safety interlocks, mold compatibility, utilities, and the maintenance file. A measurement outside tolerance, or a record that does not exist, is a reason to renegotiate or walk away.

The ten checks, in the order that finds money

Work through them in this order. The first four decide whether the machine can hold a mold and make a stable parison; the last six decide whether it can keep doing that for the next five years.

  • Clamp parallelism and platen wear. Measure the gap at four corners through the full stroke. A platen out of parallel, or deeply scored, will flash one side of the mold; regrinding or replacement is a machine-shop job.
  • Tie bars and bushings. Look for scoring, play and dry grease. Bushings are normal wear; scored tie bars usually mean the clamp ran without lubrication.
  • Screw and barrel. Ask to pull the screw, measure flight wear at feed and metering zones, and check the bore. Wear shows as falling output and drifting parison weight, and it is the most common hidden cost.
  • Die head and mandrel. Check the die lip for nicks, confirm die centering and watch the parison programmer travel. A damaged lip marks every bottle made from that head.
  • Hydraulic pump, valves and oil. Run at production pressure for at least 30 minutes and watch oil temperature, pump noise and valve leaks. Overheating points to a tired pump or a blocked cooler.
  • Heating zones and thermocouples. Heat every zone and confirm it reaches and holds set point. A dead band or a drifting thermocouple becomes wall-thickness variation you chase for weeks.
  • Control system and spare parts. Record PLC and drive brands, ask for the program backup, and confirm parameters can be saved. Obsolete controls turn a cheap machine into a parts hunt.
  • Safety interlocks. Test gate, mold-area and emergency-stop interlocks one at a time. A bypassed interlock tells you how the rest of the machine was maintained.
  • Mold compatibility. Compare platen size, clamp force and stroke against your mold drawing; clamp force must suit mold projection area and blowing pressure, not container volume alone.
  • Utilities and paperwork. Confirm voltage, phases, air consumption and cooling-water flow against your plant, then read the maintenance file, wiring diagram and spare-parts list.

The ten checks at a glance

Print this table and take it on site; the middle column is the walk-away line.

Ten-point used blow molding machine inspection checklist
Check Reject if you see What replacement involves
Clamp parallelism, platensCorner gap varies, deep scoringPlaten regrind or replacement, clamp re-alignment
Screw and barrelMeasurable flight wear, output fallingNew screw, possibly barrel, then process re-set
Die head and mandrelNicked die lip, die off-centre, programmer stickingDie repair or new head, plus re-centring
Hydraulic pump and oilOil overheating inside 30 minutes, pump noisePump or valve service, oil and filter change
Heating zonesA zone that will not hold set pointHeater band or thermocouple, temperature re-check
Controls and sparesNo program backup, obsolete boardsBoard sourcing or retrofit, often the largest cost
Safety interlocksAny interlock bypassed or deadSwitch replacement and rewiring to the original circuit
Mold compatibilityClamp or platen below your mold drawingMold rework, or a different machine
Plant utilitiesVoltage, air or water outside your plantTransformer, compressor or chiller, budgeted separately
PaperworkNo wiring diagram, no maintenance recordReverse-engineering time; treat it as a price issue

Swipe the table to see all columns →

5L Plastic Bottle Blow Molding Machine | Mold and Take-Off A representative 5l plastic bottle blow molding machine | mold and take-off clip. The machine, mold and configuration in your project may differ.

What five years of ownership does to the maths

Take a 10 L single-station machine. A new ES-10LS is specified at 110 kN clamp, 450 x 480 mm platens, a 70-75 mm screw and 80-100 kg/h output; the ES-30L and ES-50L run 80 mm and 90 mm screws with 100-160 kg/h. If the used machine needs a screw and barrel, a pump service and a control-board retrofit in year one, those items sit on top of the purchase price before the first saleable bottle. Set the asking price against a new-machine market range of roughly USD 40,000-90,000 for 5-30 L equipment, add the rebuild and the lost output, then decide. When the gap is narrow, the new machine wins on drawings, warranty and spare-part availability. The final price depends on model, mold, cavity layout, material, drive and control, and destination, so confirm it in the quotation.

If the inspection turns up wall-thickness variation,blow molding defectsandparison curl troubleshootingare the next reads. For a new-machine baseline, comparesingle-station 0-16 Landdouble-station 0-16 Lmodels, orsend the nameplate photosfor a quotation.

What to send for a quotation

  • Photos of the machine nameplate, model and serial number.
  • Photos or a short video of the clamp, screw, die head and control cabinet.
  • The maintenance file, wiring diagram and spare-parts list, if they exist.
  • Your container drawing: volume, weight, material and neck finish.
  • Your mold drawing if you intend to reuse an existing mold.
  • Plant utilities: voltage, phases, compressed-air demand and cooling-water flow.
  • Target output and shift pattern, so the machine can be sized against real demand.

Source: E-SHION product data. Specifications are subject to change without notice; customization is available.

This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.