Two double-station machines or one four-station machine: on paper both give four mold positions, and the four-station quote often looks cheaper per cavity. The difference appears after installation, in how much resin the extruder can melt per hour, how much floor the clamps take, and what happens to the line when one station needs a mold change.
Do More Stations Mean More Output?
Not by itself. A station adds a parallel mold position, but output is set by the extruder's plasticizing capacity in kg/h, by how fast the parison cools in the mold, and by how quickly the take-out clears the clamp. If the extruder cannot feed four parisons, the fourth station waits.
A four-station machine is four clamps around one extruder, or one die head feeding four parisons. The screw does not grow because the station count grew. The published pairs show this: at identical clamp force and platen, the double-station model buys a larger screw and more kg/h, not more clamp. ES-16LS runs 155 kN, a 500 x 490 mm platen, 100-120 kg/h and 7 t; ES-16LD keeps the same clamp and platen but runs 130-160 kg/h at 10 t.
What the Published Pairs Actually Show
The table is built from the published model table, not a projected layout. Read the clamp force column first: it does not change between a single and a double. The difference sits in screw, output and weight.
| Model | Stations | Clamp force | Screw | Output | Weight |
|---|---|---|---|---|---|
| ES-5LS | Single | 100 kN | 60-65 mm | 65-80 kg/h | 4.5 t |
| ES-5LD | Double | 100 kN | 70-80 mm | 100-120 kg/h | 6 t |
| ES-16LS | Single | 155 kN | 75 mm | 100-120 kg/h | 7 t |
| ES-16LD | Double | 155 kN | 90 mm | 130-160 kg/h | 10 t |
Swipe the table to see all columns →
Two things follow. Clamp force is unchanged, so a third or fourth station does not fix a clamping problem; if the mold needs more clamp, the answer is a larger platform. And the double-station gain comes through a larger screw, so the extruder remains the ceiling.
One Four-Station Machine or Two Double-Station Machines?
Four mold positions can be arranged as one four-station machine or as two double-station machines side by side. The mold count is identical; almost everything else differs. One four-station frame concentrates the hydraulics, die heads and take-out on a single base, which suits one product family running for months. Two double-station machines give two independent lines: one can change molds while the other keeps producing, and a breakdown takes out half the capacity instead of all of it.
- Mold count: four stations need four mold positions, whether that is one four-cavity tool or four separate molds.
- Floor: a four-station base is usually more compact than two separate machines, but measure it with guards, take-out and maintenance access included.
- Labour: one four-station machine is usually watched by one operator; two machines may need two people.
- Changeover: a mold change on one machine stops all four positions; on two machines the other line keeps running.
Neither layout is automatically cheaper. Two double-station machines duplicate the extruder, and that is where the cost sits; one four-station machine needs a larger extruder and a frame that carries four clamps. Put both offers on the same basis: mold count, annual output, material and labour rate.
When More Stations Stop Paying
The break-even point is not a station count; it is a ratio. Multiply your measured cycle time by the good parts per mold per cycle, then compare the result with the extruder's kg/h at your shot weight. When two stations already keep the extruder at its plasticizing limit, a third and fourth station add clamps that wait during part of every cycle.
The arithmetic is the same as any blow molding line: output equals cavities times good parts per cavity per cycle times cycles per hour, and cycles per hour is 3600 divided by the measured cycle time. A station earns its place only when it adds cavities the extruder can feed and the take-out can clear. If a four-station proposal reuses the two-station cycle time without a larger screw, ask which extruder feeds the fourth parison.
The published pairs give a quick check before any layout drawing. In the 16 L class the double-station model moves from 75 mm to 90 mm screw and from 100-120 to 130-160 kg/h, adding 3 t of machine. A four-station proposal without a comparable step in plasticizing capacity will leave the extra stations idle for part of each cycle.
What to Send for a Quotation
A station-count quote only means something when it is built on your container and your volume. Send the items below and we can compare a single-station, double-station or project-reviewed multi-station layout on one basis.
- Container drawing or sample: volume, neck and handle detail, wall-thickness target, inserts.
- Material and layer structure: PE, PP, HDPE, HDPP, PC, PVC, PETG, or a multi-layer combination.
- Annual volume and batch size, so cycle time and changeover can be weighed together.
- Mold count and cavity layout you expect, and who supplies the molds.
- Plant limits: floor space, power supply, compressed air, chiller capacity and ceiling height.
- Destination country and the documents you need for import and compliance.
If you are still weighing one clamp against two, compare the0.1-16 L single-station platformand the0.1-16 L double-station platform, check which containers fit theproduct range guide, or send the details through thecontact form.
Source: E-SHION product data. Specifications are subject to change without notice; customization is available.
This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.