A 5 L jerrycan line quoted at two prices usually comes down to one question: does a person take the bottle out of the mold, or does a robot? The semi-automatic machine is cheaper on the invoice and more expensive every shift. The answer is not a preference — it is arithmetic on your shift pattern, wage and order book.

The short answer: count shifts before you count cavities

Choose semi-automatic when you run one shift, change bottles often and labour is available at a low loaded wage. Choose fully automatic when you run two or three shifts on a stable bottle, because the operator you remove is paid every shift, while the take-out robot is paid once.

Two details qualify that rule. Station count and automation level are separate: a double-station machine puts two molds in the clamp and raises output per cycle, but it does not remove the person at take-off. And the extruder sets the ceiling — extra cavities pay only while plasticizing capacity and cooling time keep up.

What changes at the machine, hour by hour

On a semi-automatic extrusion blow molding machine the operator is part of the cycle: open the guard, lift out the bottle and flash, check the neck and pinch-off, trim, stack, close the guard. A 5 L bottle is not heavy, but the motion never stops, so hourly output is a range set by how long a person can keep repeating it — and it narrows on nights.

A fully automatic line gives that work to a take-out robot, a conveyor and, where the bottle allows, in-line deflashing. The operator stops handling every part and starts supervising: weighing samples, checking wall thickness, clearing jams, recording scrap. One person can then cover more than one machine, which is where the saving comes from.

  • Time a full cycle with the operator in the loop, then again with the take-out device running.
  • Count every touch: take-off, trimming, gauging, stacking, packing. Each one decides headcount and scrap.
  • Weigh 20 bottles per cavity and check wall thickness; manual trimming can hide variation.
  • Confirm whether gripper, conveyor and trimming are inside the quoted scope.

Cost across one, two and three shifts

The comparison is three lines of arithmetic, not a machine price. For each shift pattern, multiply operators per shift by machine hours per year, then by the fully loaded hourly cost of labour — wage, insurance, meals, transport and supervision. Add the scrap difference, then compare with the extra capital for robot, conveyor and trimming.

Semi-automatic vs fully automatic: where the payback moves
Decision point Semi-automatic Fully automatic
Bottle take-offOperator lifts each bottle and the flash by handTake-out robot or conveyor; mold and cooling set the pace
People per shiftUsually one operator per machineOne supervisor covers several machines plus sampling
Trimming and flashManual at the machine; finish depends on skillIn-mold or in-line where the design allows
Scrap patternDrops, scratches, dirt, uneven trimmingFewer touches, but jams and gripper marks appear
Robot investmentNone in the base scope; manual take-offRobot, gripper, conveyor and safety circuit as a package
Best fitOne shift, high mix, short runs, labour availableTwo or three shifts, stable bottle, tight labour

Swipe the table to see all columns →

The table names no winner because the third shift changes the answer. On one shift, roughly 2,400 machine hours a year, the robot has little time to earn back. On three shifts the same robot runs about 7,200 hours against three wages. The shift plan belongs at the top of the comparison, not the machine specification.

  • One shift, about 2,400 hours a year: keep the semi-automatic machine and spend the difference on a second mold.
  • Two shifts, about 4,800 hours: the second operator is permanent, so price the robot against two wages.
  • Three shifts, about 7,200 hours: night supervision and turnover cost more than the day rate, and automatic take-off is easiest to justify.

Where the money hides: scrap, changeover and used machines

Labour is the visible cost; scrap is the quiet one. Manual take-off adds at least two handling touches per bottle, and each can drop, scratch or contaminate the part. On a food or lubricant container the reject is not only the plastic: it is sorting time, regrind decisions and the risk of a contaminated lot reaching your filler. Measure scrap by shift for a month.

Used equipment splits the decision. A used semi-automatic machine is the lowest-capital entry into 5 L work, but screw and barrel wear, clamp condition, hydraulic seals and control spare parts decide whether it is a bargain or a project. A used automatic line adds a robot whose controller and gripper may already be obsolete.

5L Plastic Bottle Blow Molding Machine | Mold and Take-Off A representative 5l plastic bottle blow molding machine | mold and take-off clip. The machine, mold and configuration in your project may differ.

A decision path for a 5 L jerrycan line

Take a 5 L HDPE jerrycan, one shift today, a possible second shift next year. The single-station ES-5LS lists a 100 kN clamp, a 320 × 380 mm platen, a 60–65 mm screw and 65–80 kg/h output. The double-station ES-5LD lists the same clamp, a 70–80 mm screw and 100–120 kg/h. Neither figure says who removes the bottle. For one shift, the ES-5LS with a well-cooled mold is the lower-risk start; if a second shift is likely, price the ES-5LD and a take-out device together.

Either way, the output check is the same: cavities × good parts per cavity per cycle × cycles per hour, with cycles per hour equal to 3,600 divided by a cycle time you measured on a trial. Compare that with the extruder's plasticizing capacity; on a double-station machine the extruder is usually the limit, not the clamp.

Machine data for both models is on thesingle-station 0–16 L pageand thedouble-station 0–16 L page. For the arithmetic, readcavity output calculationand theROI framework.

What to send for a quotation

Send these and the reply can be a comparison instead of a single number. The more you send, the fewer assumptions sit behind the price.

  • Bottle drawing or sample: volume, neck finish, weight, wall-thickness target, material and regrind percentage.
  • Shift plan: shifts per day, days per week, and whether a second or third shift is decided or only possible.
  • Current line data: measured cycle time, operators per shift, scrap by shift, rework hours.
  • Fully loaded local labour cost: wage plus insurance, meals, transport and supervision.
  • Automation scope: manual take-off, robot only, or robot with conveyor and trimming, and who supplies the safety circuit.
  • Site limits: ceiling height, power, compressed air, chilled water and aisle width for a conveyor.

Source: E-SHION product data. Specifications are subject to change without notice; customization is available.

This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.