A lower machine price can still mean a more expensive production line. The machine price is paid once; material, energy, labor and scrap are paid on every bottle. Ask what one good bottle costs and how many the line can sell monthly.

The short answer: cost per good bottle, then capital recovery

ROI asks what one good bottle costs and how much contribution the line generates monthly. Bottle cost = (material + energy + labor + consumables + mold amortization) ÷ good bottles. Payback = total project investment ÷ monthly contribution.

Plain rule: if you cannot state four numbers — part weight, measured cycle time, good-part rate and local power tariff — treat any payback figure as a guess. Get them first; comparison becomes arithmetic, not impression.

The five lines in a bottle's cost

Keep the lines separate. Folding capital recovery into variable cost hides where the money goes and blocks comparison.

  • Material. Part weight × resin price ÷ good-part rate, less recovered regrind value. Here, 10 g on a 160 g bottle is about 6% of material cost.
  • Energy. Metered kWh per hour × tariff ÷ good bottles per hour. Nameplate power is not consumption: ES-5LS lists 32–42 kW installed, ES-10LS 38–48 kW, ES-30L 100–110 kW.
  • Labor. Operators per shift, including take-off and packing, × hourly cost ÷ good bottles per hour. Automation changes this line and first cost together.
  • Consumables and spares: pinch-off inserts, filters, lubricants and small wear parts. Small per bottle, but still variable cost.
  • Mold amortization. Mold cost ÷ planned good parts. Market ranges: roughly USD 2,000–5,000 for a simple two-cavity mold and USD 15,000–35,000 for larger multi-cavity tools; lead time commonly 20–60 days after drawing approval. Confirm in the quotation.

Two worked examples: 5 L and 20 L

Both assume two shifts and 90% good parts. The 5 L bottle uses two cavities and a 30 s example cycle; the 20 L container uses one cavity and a 55 s example cycle. Placeholder inputs: resin USD 1.20/kg, power USD 0.10/kWh, labor USD 3.00/operator-hour; not local quotes.

Illustrative cost per good part, excluding consumables and spares. Placeholder inputs, not E-SHION specifications or quotations; replace with your measured and local values.
Cost line 5 L HDPE bottle (example) 20 L HDPE container (example)
Example inputs160 g, 2 cavities, 30 s, 90% good700 g, 1 cavity, 55 s, 90% good
Good output216 per hour59 per hour
MaterialUSD 0.21USD 0.93
EnergyUSD 0.012USD 0.11
LaborUSD 0.014USD 0.10
Mold amortizationUSD 0.002USD 0.02
Cost per good part before consumables, regrind credit and overheadabout USD 0.24about USD 1.16

Swipe the table to see all columns →

Material dominates the cost shown: about 88% of the 5 L cost and 80% of the 20 L cost. Resin price, part weight and wall-thickness control matter more than a modest machine discount. Energy and labor matter more where power is expensive or automation limited.

The output formula is worked through in the blow molding cavity and output calculation; machine price bands are in the blow molding machine price guide.

Payback: project total against monthly contribution

Payback starts from the whole project: machine + mold + auxiliaries + freight, insurance and installation + working capital for resin, spares and receivables. Machine-only market ranges are roughly USD 25,000–70,000 for 1–5 L and USD 40,000–90,000 for 5–30 L; the final price depends on model, mold, cavity layout, material, drive/control and destination. Confirm the scope in the quotation.

Contribution per bottle = selling price − variable cost (material, energy, labor, consumables). Mold amortization and depreciation are capital recovery; if already in bottle cost, do not subtract again.

Example: table output, 5,000 hours/year. 5 L line: 216 bottles/hour × 5,000 = 1.08 million bottles; at USD 0.08 contribution, USD 86,400/year. Example project: machine 45,000 + mold 3,000 + other project costs 25,000 = USD 73,000, about 10 months. 20 L line: 59 containers/hour × 5,000 = 295,000; at USD 0.35 contribution, USD 103,250/year. Example project: machine 75,000 + mold 20,000 + other project costs 50,000 = USD 145,000, about 17 months. Arithmetic examples, not forecasts.

30L Plastic Container Blow Molding Machine | Mold and Clamp Run Representative 30 L mold and clamp run. The clip shows machine movement, not your cycle time; configuration and container may differ from your project.

What to send for a quotation

A quotation you can put into the formula needs:

  • Container drawing or 3D file with neck, handle and base detail; volume, part weight, wall thickness and material.
  • Target good output, shift pattern and annual operating hours.
  • Measured cycle time and good-part rate from an existing line, if you have one.
  • Local electricity tariff, available power, water, compressed air and floor space.
  • Resin price, regrind policy and existing mold, if any.
  • Destination port and delivery terms.

A sample with a ruler in the photo and its part weight is enough to start.

Send the details through the contact page, or review the 0–16 L single-station series and the 20–50 L single-station series.

E-SHION MACHINERY, Taizhou, Zhejiang, China. https://www.e-shionmachinery.com. WhatsApp +86 151 6778 9726. Email doris@e-shionmachine.com

Source: E-SHION product data. Specifications are subject to change without notice; customization is available.

This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.