A four-cavity mold looks like four times the output of a single-cavity mold, and plenty of quotations are built on that multiplication. In production the multiplier rarely survives the extruder: the screw can only plasticize so many kilograms per hour, the mold can only release heat so fast, and the take-off can only clear so many parts per minute. Calculate output in pieces per hour, then check it in kilograms per hour. That is how you avoid paying for cavities that buy only a longer cycle.
The short answer: calculate output, then choose the cavity count
Start from the annual volume and the shift pattern, not from a cavity number. Work the chain: measured cycle time, cycles per hour, gross parts, material demand in kg/h, good parts, then the comparison with published extruding capacity. If material demand sits inside the range with margin, the cavity count is viable. If not, the cycle will run longer than you assumed. Heavy parts favor fewer cavities; small parts, short cycles and a big extruder can justify four or six.
The formula, term by term
The arithmetic is simple. The discipline is in what you put in each slot.
- Cavities: the part positions actually cut in the mold, not the number of die heads.
- Cycle time: measured on the real mold, material and cooling, from mold close to mold open. A dry cycle is not a planning number.
- Cycles per hour: 3600 ÷ cycle time in seconds. A 22-second cycle gives about 164.
- Gross parts: cavities × cycles per hour.
- Efficiency: one planning factor that combines uptime and yield. Apply it once, and write the assumption into the quotation.
Good parts are gross parts × efficiency. The step most often skipped is the material check: multiply gross parts per hour by part weight and compare the result with the model's published extruding capacity. Material demand is based on gross parts because every cycle consumes a parison, including parts rejected later. Pieces and kilograms are two views of the same limit, and the screw only answers to kilograms.
Worked examples: a 5 L four-cavity job and a 30 L two-cavity job
The cycle times and part weights below are arithmetic inputs, not published E-SHION figures. Replace them with values measured on your own mold and material. The 5 L case is compared with the ES-10LS and the 30 L case with the ES-30L; confirm each cavity layout against the platen drawing.
| Line | 5 L example | 30 L example |
|---|---|---|
| Cavities | 4 | 2 |
| Assumed cycle time | 22 s | 65 s |
| Cycles per hour (3600 ÷ cycle) | 164 | 55 |
| Gross parts per hour | 655 | 111 |
| Assumed part weight | 125 g | 1.2 kg |
| Material demand (gross parts × weight) | 82 kg/h | 133 kg/h |
| Planning efficiency (assumed) | 85% | 85% |
| Good parts per hour | 556 | 94 |
| Published extruding capacity | ES-10LS: 80–100 kg/h | ES-30L: 100–120 kg/h |
| Read-across | Near the bottom of the range; little headroom | Above the range; the cycle stretches or a cavity must go |
Swipe the table to see all columns →
Read the last two rows first. The 5 L job needs 82 kg/h, near the bottom of the ES-10LS range of 80–100 kg/h: the arithmetic works, but the headroom is thin, and a faster cycle runs into the screw. The 30 L job needs 133 kg/h against the ES-30L's 100–120 kg/h, so 65 seconds at two cavities demands more material than the published output can supply. Expect one of three outcomes: a longer cycle, a one-cavity job, or a trial before the mold is cut. Neither result is a verdict on the machine; both tell you what to test.
To run the same table on your own job, replace the cycle time and part weight, keep the order of operations, and stop where material demand reaches the top of the published range. That point is the cavity count the extruder can support at that cycle.
Why the extra cavity often does not pay
Three limits sit behind the formula. Plasticizing capacity: every cavity needs a parison each cycle, and published kg/h is the ceiling. Cooling: more cavity area means more heat to remove, and thick sections cool from the outside in. Take-out: a take-off sized for a single-cavity mold may not keep up with four.
Clamping is the fourth check. More cavities usually mean a larger mold projection area, and clamp force must hold that area against blowing pressure. Compare the requirement with the published clamp, 110 kN on the ES-10LS, using the mold drawing, not container volume. A mold that fits the platen can still be under-clamped.
Cost belongs in the same sum. A larger multi-cavity tool commonly falls in the market range of roughly USD 15,000–35,000, against roughly USD 2,000–5,000 for a simple two-cavity bottle mold. Treat both as market ranges, not quotes: the final figures depend on model, mold, cavity layout, material, drive and control, and destination; they are confirmed in the quotation.
If the extra cavity means a second mold position, read single-station vs double-station. Published clamp, screw and output figures are on the 0.1–16 L single-station series and double-station series pages.
See a multi-cavity cycle before you fix the count
A clip is not a trial, but it shows what the arithmetic describes: several parisons, one clamp, a take-off rhythm that must keep up.
Watch the interval from clamp close to take-off, not the parts. That interval, repeated, is the cycle time worth entering the formula. The clip cannot give seconds, part weight or yield.
What to send for a quotation
A cavity count is only useful with the numbers behind it. Send these and the reply can check your calculation.
- Container drawing or 3D file with height, diameter, neck and handle.
- Part weight and wall-thickness range, per cavity.
- Material grade, plus barrier or recycled-content requirements.
- Target annual volume, shift pattern and output per hour.
- The cycle time you assume, and where it came from.
- Existing mold data: cavity layout, dimensions, weight and previous machine.
- Destination voltage, frequency, air and cooling water available.
If the mold is not cut yet, say so. Cavity layout, die-head spacing and clamp force then have to be designed together, before the purchase order.
The right cavity count is the one whose worst number, kg/h at your measured cycle, still fits the machine.
Send the list through the contact form; above 16 L, compare the 20–50 L single-station platform.
Source: E-SHION product data. Specifications are subject to change without notice; customization is available.
This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.