A jerrycan can pass every drop and pressure test and still be stopped at the border, because the label is wrong. Labelling is where the container, its intended use and the destination market meet, and the rules diverge sharply. A UN mark is mandatory on dangerous-goods packaging and meaningless on a food jar; a food-contact statement is essential on the jar and irrelevant on a solvent can. The mark list should be fixed before the mold is cut, not after the first print proof.

Mandatory marks follow use and market, not the machine

Mandatory marks depend on what the container holds and where it is sold, not on the blow molding machine. Four groups cover most cases: dangerous-goods UN marks, material identification, food-contact statements, and producer, origin and batch details. Everything else — brand, dosing instructions, recycling appeals — is a buyer mark. Agree the full list before the mold layout is fixed.

The four mark groups in practice

The UN mark appears only on packaging that has passed UN performance tests for dangerous goods. On an HDPE jerrycan it typically carries the UN symbol, the packaging code (31H1 for a non-removable head, 31H2 for a removable head), a performance level of X, Y or Z, the relative density, the hydrostatic test pressure where applicable, the year of manufacture, the country and the maker's code. That string belongs to one tested design. It cannot be copied onto another container, even one of the same nominal size, without new testing.

Material identification is a separate layer. EU packaging has carried resin identification codes under the packaging and packaging waste rules; from 12 August 2028 the PPWR harmonised material label applies. In the US and China, recycling marks are mostly voluntary or buyer-driven, so the same container may carry an EU-style code for one customer and none for another. Print plates should follow the market, not the mold.

  • Dangerous goods: the UN mark plus the hazard labels and shipping information the transport mode requires.
  • Food contact: a statement naming the material and the conditions of use, backed by a declaration of compliance.
  • Origin: country-of-origin marking where the importing country requires it; the wording is usually set by the buyer.
  • Traceability: batch, shift or date code, often a mold insert or an ink-jet block that has to fit inside the label panel.

Three-market label matrix

The matrix below is a working map of plastic packaging labelling requirements across the three markets. Treat it as a planning frame: confirm each SKU against the current legal text and the packaging's own test certificate.

Typical label elements for a blow-molded HDPE container by market. Requirements depend on the product's use; verify each SKU against the current legal text.
Mark European Union United States China
UN dangerous-goods markRequired on dangerous-goods packaging; details from the UN test certificateRequired; UN mark plus hazmat shipping labelsRequired; follows dangerous-goods packing rules
Material identificationResin code today; harmonised PPWR label from 12 Aug 2028No general federal mandate; state and buyer rules varyNot generally mandatory; common as a buyer mark
Food-contact statementStatement plus declaration of complianceMaterial must meet FDA food-contact rules; statement often a buyer requirementGB 4806 labelling items apply
Producer / importerName and address of producer or importerName and place of businessManufacturer or importer name, address and contact
Country of originWhere customs or the buyer requires itRequired on imported goodsDeclared according to customs rules
Batch / date codeBuyer and traceability requirementBuyer and traceability requirementProduction date or batch

Swipe the table to see all columns →

30L Plastic Container Blow Molding Machine | Large Container Production A representative 30L plastic container blow molding machine | large container production clip. The machine, mold and configuration in your project may differ.

Where the label meets the blow molding process

Three design decisions decide whether the label works. The label panel should be flat and slightly recessed, because a curved surface distorts a long UN string and makes a wrap-around label bridge at the corners. Wall thickness at the panel matters too: a panel that flexes under hand pressure will crack the print or lift the adhesive. The date-code area is the third — a small recessed window or a raised boss keeps the code legible without cutting into the label.

The usual order is to fix the container's use first, list the mandatory marks second, size the label panel third, and release the mold drawing last. A print file can be changed in an afternoon; a label panel changed after the mold is cut means reworking the mold, re-polishing and, for dangerous goods, re-testing the design.

A 12 L industrial container follows the same label logic; the12 L container blow molding guidecovers parison and wall-thickness choices, and thesingle-station 0–16 L serieslists the models usually paired with these molds.

What to send for a quotation

A label question usually turns into a mold question. Send these and the quotation can cover the machine, the mold and the label panel in one pass:

  • Container drawing with the label panel size and the flat print area marked.
  • Intended use: dangerous goods with its UN specification, food contact, or general industrial.
  • Destination market and the exact mark list your customer requires, including language versions.
  • Annual volume, cavity count and material, whether HDPE, PP or a coextruded structure.
  • Date-code method — mold insert, ink-jet or laser — and the position the code must take.

If the mark set is still open, send the drawing anyway andcontact our team— we will list what the mold has to leave room for.

Source: E-SHION product data. Specifications are subject to change without notice; customization is available.

This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.