Three quotations for the same 10 L bottle can arrive with three different drive packages, and the lowest purchase price is not automatically the lowest cost per good part. Electricity, hydraulic oil and filters, response at the clamp, and the technician needed to keep the line running all land in the same account. The useful question is not which drive is better, but which drive fits this container, this shift pattern and this maintenance team.
The short answer: match the drive to the shift
Use this rule before comparing prices:
- One container, one or two shifts, a tight budget and a workshop that already maintains hydraulics: a hydraulic machine is usually the lowest-risk entry. The circuit is familiar, service is easy to arrange, and quotations are simpler to compare.
- Several SKUs, frequent mold changes, stop-start production, or a cycle that must be trimmed for each mold: price servo-hydraulic. The servo pump delivers oil on demand instead of running flat out, and clamp response is more repeatable.
- High-value cosmetic parts, long runs and a plant that wants a clean line without a hydraulic oil circuit: evaluate all-electric, provided you can support servo diagnostics and the higher first cost.
- If the price gap between two packages is small against a year of electricity, decide on uptime, spare parts and service response instead of an energy label.
This is not a ranking. A well-maintained hydraulic machine can run more steadily than a badly specified servo package; the drive only helps when the mold, cooling and extruder are matched to the job.
Where the money and the downtime sit
The drive touches five things a buyer pays for:
- Response. A hydraulic clamp moves on oil pressure and valve response; a servo-hydraulic pack varies pump output; an all-electric clamp moves on servo motors. Faster response can shorten the dry cycle, but it becomes output only if cooling and extrusion keep pace.
- Energy. A fixed-speed pump keeps running at idle, even when no axis moves; a servo pump delivers closer to demand; all-electric axes draw mainly when they move. Heaters, chiller and compressor sit outside that comparison. Measure at the machine intake, not from the nameplate.
- Maintenance. Hydraulic machines need oil, filters, seals, hoses and oil-temperature control. Servo-hydraulic adds pump and drive electronics; all-electric removes the main oil circuit but adds servo motors, drives and diagnostics. A cheap drive can be expensive to keep if local skills are thin.
- First cost. Hydraulic is normally lowest, servo-hydraulic in the middle and all-electric highest. The gap buys response, repeatability and possibly lower idle energy, not proof of lower total cost.
- Shift output. Output is cavities × good parts per cavity per cycle × cycles per hour, and cycles per hour = 3600 / measured cycle time. The extruder plasticizing capacity is the ceiling; a faster clamp cannot feed itself.
This is why two factories can both be right. A one-shift plant running a single bottle may never recover the price gap of an all-electric package. A three-shift plant changing molds daily may lose more to slow changeover and unstable cycles than it saves on the purchase.
What a drive change will not fix
A more expensive drive will not correct a mold water circuit that cools unevenly, a die that is off-center, or heater bands that drift. Wall-thickness variation, parison curl, weak pinch-off and neck ovality are process and tooling symptoms first. Check die centering, die gap, temperature uniformity, blow-pin alignment and cooling before blaming the drive.
The drive does not add clamping force either. Clamp force must be checked against mold projection area multiplied by blowing pressure, plus a margin, not container volume alone. If the mold is near the limit, the answer is a larger clamp, not a faster pump.
Compare on five points, then read the meter
If the servo-hydraulic or all-electric package costs more, run the arithmetic: price gap / (annual kWh saved × your tariff) = simple payback in years. Estimate maintenance and downtime the same way. Use your own tariff and running hours, not the supplier's. A payback longer than the service life you plan for makes the cheaper drive the rational choice, even if it uses more energy.
| Drive | Response and repeatability | Energy behavior | Maintenance load | First cost and typical fit |
|---|---|---|---|---|
| Hydraulic | Proportional valve control; stable on a fixed cycle; response depends on pump and valve size | Fixed or variable pump; the pump keeps running at idle; heat goes into the oil | Oil, filters, seals, hoses and oil cooling; familiar to most workshops | Lowest; one product, one or two shifts, budget-led |
| Servo-hydraulic | Servo pump follows demand; faster and more repeatable than a standard hydraulic pack | Pump output tracks the motion; idle draw can fall; verify at the machine intake | Hydraulic care plus servo pump and drive electronics | Middle; mixed SKUs, frequent starts and stops, long shifts |
| All-electric | Servo axes on clamp, carriage and blow functions; repeatable positions; no main hydraulic oil circuit | Draws mainly when axes move; check drives, regeneration and auxiliaries | No main oil circuit; servo motors, drives and diagnostics; needs trained staff | Highest; high-value parts, clean line, high utilization |
Swipe the table to see all columns →
The short clip below shows the control screen and clamp cycle of a representative 5 L bottle run. It is useful for judging sequence and response; it cannot show energy consumption.
For the output formula, read how cavity count and cycle time set output; for the full selection sequence, read how to choose an extrusion blow molding machine. The ES-10LS sits in the 0–16 L single-station series, with 110 kN clamping force and 450 × 480 mm platens.
What to send for a quotation
A drive comparison is only useful when every supplier prices the same scope. Send:
- Container drawing or 3D file with volume, part weight, wall thickness, material and neck finish.
- Cavity count, existing mold drawing and weight, and whether the old mold must be reused.
- Target good parts per hour and the shift pattern, including start-stop and mold-change frequency.
- Plant voltage, frequency, transformer capacity, compressed air and water supply; say whether you want an energy meter included.
- The drive and control package you want priced, and whether you require a measured energy run on the same mold and material at the factory acceptance test (FAT).
- Destination port, delivery terms, and the spare parts and maintenance training you expect the supplier to cover.
Ask for the drive and control package as a separate line item, not something implied by a model code. If a saving is claimed, ask for the measurement method, the baseline and the operating conditions. Only then can the quotations be compared.
E-SHION MACHINERY, Taizhou, Zhejiang, China. https://www.e-shionmachinery.com. WhatsApp +86 151 6778 9726. Email doris@e-shionmachine.com
Source: E-SHION product data. Specifications are subject to change without notice; customization is available.
This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.