A two-second saving sounds small until it is multiplied by every cycle and shift. It is also the wrong two seconds if the mold waits for take-out while the cooling timer is shortened. Before buying a faster machine or a robot, break the cycle into segments and find the longest one. A common mistake is to speed up a step that was already waiting, then count a saving that never reaches output.
The short answer: find the bottleneck, then cool the part
Cycle time is not one setting. It is clamp close, parison drop, blow, cooling, mold open and take-out, and some motions overlap. The cycle equals the longest path, not the sum of every timer. Use the symptom to find the limit before touching a setpoint.
A simple rule: if the part is still soft when the mold opens, work on wall thickness and cooling before touching a timer. If the mold stands open with the part already out, the limit is take-out, not cooling. A job that cuts three seconds of cooling but still waits for the operator has saved nothing.
- Part still soft at take-off: cooling or wall thickness limits the cycle.
- Mold open, part out, machine waiting: take-out limits the cycle.
- Mold closes before the parison is ready: plasticizing limits the cycle.
Break the cycle into segments before changing anything
Use the machine timer and a stopwatch on a normal run, with the real mold and material, for at least ten cycles. Record each segment and any idle time. The cooling timer is not the cooling time: the part keeps losing heat during mold open and take-out, and thick sections cool after ejection. Watch mold close to mold close.
Put the four segment times and any wait on one sheet. If nobody can name the longest segment, the line is being tuned by guesswork; ten timed cycles settle that faster than a new machine quotation.
- Mold close to blow start: clamp motion, blow delay, blow-pin travel.
- Blow to mold open: blowing, holding and the cooling timer.
- Mold open to clear: opening speed, take-out and waiting.
- Clear to next close: placement, conveyor, safety door, robot return.
Five levers, in the order that usually pays
This order suits a job already in production. Change one lever at a time and re-measure; two changes at once hide which one worked.
| Lever | What it changes | First check | Limit or risk |
|---|---|---|---|
| Wall thickness / parison profile | Heat in the part; thin sections cool first | Section weights and wall map | Below drawing minimum, drop and top-load may fail |
| Mold temperature | Temperature difference driving heat out | Mold-surface temperature at several points | Too cold can hurt surface and stress; set by material and trial |
| Cooling circuit | Flow at neck, body, base and pinch-off | Series or parallel, branch flow, inlet-outlet rise, scale | No flow means no cooling, however cold the inlet |
| Blow pressure and venting | Parison-to-mold contact; air escape | Pressure at mold, blow-pin seal, vents | More pressure costs air and raises clamp demand; trapped air insulates |
| Take-out automation | Mold-open time waiting for a person | Mold open to clear, gripper clearance | Hot parts deform or mark; match mold and conveyor |
Swipe the table to see all columns →
If you raise blow pressure, recheck clamp force: mold projection area × blowing pressure, plus a margin. The ES-10LS's published clamp is 110 kN, and whether that is enough depends on your mold drawing, not container litres alone.
The extruder is the sixth check, not the first. If the parison arrives late, more screw speed may only give a hotter, less uniform melt. Compare the job's kg/h demand with published output — ES-10LS published output is 80–100 kg/h — before adding cavities or speed.
What two seconds are worth
The arithmetic is the output formula with cycle time as the variable: parts per hour = cavities × good parts per cavity per cycle × (3600 ÷ measured cycle). Cavity and kg/h checks are in the output-calculation guide; here the question is the value of a second.
Example: two cavities, a 10 L part, 45 seconds and 85% planning efficiency. At 45 seconds: 80 cycles per hour, 160 gross parts, 136 good. At 43 seconds: about 84 cycles, 167 gross, 142 good. Two seconds add about 6 good parts per hour, or 50 per eight-hour shift. These are arithmetic inputs, not an E-SHION cycle time; use measured values.
Multiply extra good parts by contribution per part, then compare the annual figure with the cost of the change: cooling work, a take-out robot, a mold modification or a different machine. Percentage matters more than seconds. Two seconds off a 12-second small-bottle cycle is 17%; off a 45-second thick part it is under 5%.
Watch the clamp and take-off, not just the timer
The clip shows the clamp and bottle take-off area of a 5L machine. Watch the mold-open interval and how the bottle leaves the mold; that is the part a take-out change can shorten.
After the part is clear, any remaining open time is take-out. If a robot or an operator is the wait, a second off cooling adds nothing; match gripper clearance and conveyor speed first.
A clip cannot give your cycle time, wall thickness or cooling flow. Use it to see the motion sequence, then measure your own clamp-to-clamp time.
What to send for a quotation
A cycle question needs the current cycle, not only the container. Send these and the reply can separate a machine limit from a mold or take-out limit.
- Container drawing or 3D file, with part weight and wall map.
- Material grade, regrind ratio and any barrier layer.
- Current cycle and segment breakdown: clamp, parison, blow, cooling, mold open, take-out.
- Mold drawing: cavity layout, mold height, cooling channels, core baffles.
- Blow pressure, air supply, cooling water temperature and flow.
- Target output, shift pattern and planned take-out method.
- Existing machine model, control and measured idle time.
If the line is not running yet, send the target container and the cycle you need to hit. The reply can check mold, clamp and published output capacity before a model is quoted.
Send the drawing and cycle data to E-SHION MACHINERY, Taizhou, Zhejiang, China. Website https://www.e-shionmachinery.com; WhatsApp +86 151 6778 9726; email doris@e-shionmachine.com
For cavity and kg/h arithmetic, read blow molding output calculation. For the wall map behind the first lever, read blow molding wall thickness control. For the process behind the cycle, read how extrusion blow molding works. Published figures for the 0.1–16 L platform are on the single-station series page; send the list through the contact form.
Source: E-SHION product data. Specifications are subject to change without notice; customization is available.
This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.