A 30 L drum inquiry comes back with an accumulator head. The same buyer asks about a 5 L jerrycan and is offered a continuous extrusion machine. It looks like supplier preference; most of the time it is a response to shot weight and parison length. The mismatch does not show on the quotation. It shows after installation — as parison sag, uneven wall, a cycle that never reaches the quoted rate, or a mold that cannot be fed fast enough.

The short answer: let the shot and the parison decide

The choice is a process match, not a ranking. An accumulator head stores a measured shot of melt and pushes it through the die as one timed parison; that suits large, heavy parts and long parisons, where the parison has to reach the mold quickly before it sags. Continuous extrusion delivers the parison steadily; that suits small and medium parts and faster cycles, where the parison does not hang long or travel far.

For a first screening, use three rules:

  • The part is large or heavy and the parison is long enough that sag is a real risk — put the accumulator route on the table.
  • The part is small or medium, the cycle is short and the mold can take the parison without a long wait — start with continuous extrusion.
  • The requirement sits between the two — decide on a trial with your mold and material, not on a capacity table.

Neither route is automatically better. A large part can be run on continuous extrusion and a small part can be run on an accumulator head. What matters is whether the shot, the parison, the clamp and the cooling match the mold — and whether the supplier will prove it on your cycle.

What changes on the shop floor

The head type changes four things the buyer feels after installation:

  • Parison delivery. An accumulator head pushes the shot when the mold is ready. Continuous extrusion delivers a steady parison, so mold movement, cut-off and take-out have to keep pace.
  • Sag and wall. A long parison hanging before mold close is exposed to gravity and cooling. Wall control still depends on the parison programmer, die-gap profile, die centering, heater bands and temperature uniformity, whichever head is used.
  • Cycle rhythm. Continuous extrusion rewards a short, repeatable cycle. An accumulator adds a fill-and-push sequence to each cycle — the cost of delivering a large shot in one stroke.
  • Start-up scrap. Every trial part on a large container uses a full part's worth of material. The heavier the shot, the more each learning cycle costs.

Ask for the head type in writing, with the shot weight it is sized for and the parison length it must deliver. If those two numbers are missing from the proposal, the head has not been engineered for your container yet.

Cost and energy: compare the good part, not the kW

Head type is one line in a project that also includes clamp, screw, drive, mold, chiller, compressor and take-out. Do not compare machines by installed power. Installed kW is not running consumption, and the two heads do not load the hydraulic system in the same way. The useful figure is measured kWh per good part on your mold, material and cycle. Ask for it, and ask how it was measured.

For budget screening, the market frame is roughly USD 25,000–70,000 for 1–5 L machines, USD 40,000–90,000 for 5–30 L and USD 60,000–120,000 for 30–50 L; a 30 L machine sits where the last two frames overlap. These are market ranges, not E-SHION quotations. Head type, model, screw, drive and control, mold, cavity layout, material and destination all move the final number. Confirm the final figure in the quotation. Molds are usually quoted separately: roughly USD 2,000–5,000 for a simple two-cavity bottle mold and USD 15,000–35,000 for larger multi-cavity tools, commonly 20–60 days after drawing approval. Auxiliaries are separate as well.

Where the line falls: five container examples

The table is a screening guide for the first technical conversation, not a selection result. The platform column shows the E-SHION range whose clamp and platen envelope fits the container; the head route is confirmed on the mold drawing and, where needed, a trial.

Container examples, the head route to evaluate, and the platform to price — market frame only
Container example What usually drives the choice Head route to evaluate Platform to price Market frame
2 L HDPE bottle, multi-cavityShort parison, fast cycle, cavity-to-cavity consistencyContinuous extrusion is the natural startES-2LS / ES-2LDUSD 25,000–70,000 (1–5 L)
5 L jerrycan, 1–4 cavitiesMedium shot, integral handle, wall targetContinuous extrusion for short cycles; compare if the parison is long for the moldES-5LS / ES-5LDUSD 25,000–70,000 (1–5 L)
12–16 L containerLonger parison, heavier part, mold heightCompare both; the accumulator route moves up as shot and parison growES-16LS / ES-16LDUSD 40,000–90,000 (5–30 L)
20–30 L drum or jerrycanHeavy shot, long parison, sag risk before mold closeEvaluate the accumulator route firstES-30LUSD 40,000–90,000 (5–30 L frame; 30 L sits at the overlap)
50 L drumLargest container in the range, long parison, large moldEvaluate the accumulator route with a full clamp and shot checkES-50LUSD 60,000–120,000 (30–50 L)

Swipe the table to see all columns →

Two checks apply to every row. First, clamp force: mold projection area × blowing pressure, plus a safety margin — litres alone do not size the clamp. On the 0–16 L models the published clamp is 100 kN at 2 L and 5 L, 110 kN at 10 L and 155 kN at 16 L; on the 20–50 L platform it is 215 kN for the ES-30L and 260 kN for the ES-50L. Whether that is enough depends on your mold drawing. Second, output: cavities × good parts per cavity per cycle × cycles per hour, where cycles per hour is 3600 ÷ measured cycle time. Changing the head does not change that arithmetic.

A 20 L part can need more clamp than a 30 L part if its mold has the larger projected area. That is why the drawing, not the litre figure, is the input to the head and clamp decision.

For the machine envelope, read the extrusion blow molding selection guide. For large containers, see 20–50 L container production; for the process family, compare extrusion vs injection blow molding.

30L Plastic Container Blow Molding Machine | Mold and Clamp Run Representative clip: mold and clamp run on a 30 L container machine. The head type, mold and container may differ; the clip is illustrative, not a cycle statement.

What to send for a quotation

A head recommendation cannot be quoted from a volume. Send these items so the head, shot and clamp are checked on the same assumptions:

  • Container drawing (2D/3D): outer dimensions, neck, handle, base and wall-thickness target.
  • Part weight and material grade (HDPE, PP, HDPP, PVC; multi-layer or EVOH if required).
  • Parison length or mold height, if already known.
  • Cavity count and target output, or annual volume and shift pattern.
  • Existing mold drawing, dimensions, weight, mounting details and clamp requirement.
  • Destination country, voltage, and available air and cooling water.
  • Scope: machine only, machine plus mold, or a line with auxiliaries, installation and training.
  • Whether a trial with your material and mold is required before acceptance.

Send the drawing to doris@e-shionmachine.com or WhatsApp +86 151 6778 9726. The quote form opens with ES-30L prefilled; attach the container drawing so the head route, shot size and clamp can be reviewed as one proposal.

Source: E-SHION product data. Specifications are subject to change without notice; customization is available.

This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.