Juice is one of the few bottle categories where the resin is still an open question. A brand owner specifies a 500 ml or 1 L bottle, the filler quotes a hot-fill line, and someone asks whether the bottle has to be PET at all. That decision changes the machine, the mold, the cycle and the clarity a shopper sees on the shelf, so it is worth settling before a mold drawing is approved.
The short answer: fill temperature decides first
Choose clarified PP when the juice is hot filled up to about 98°C or the bottle is tinted, and run it on an extrusion blow molding machine. Choose PET when the product is cold filled and the shelf needs glass-like transparency. Clarity and output follow that first decision, not the other way round.
Clarity: clarified PP is close, not identical
PP is semi-crystalline. Untreated, a PP bottle is translucent rather than water clear, which is why early PP juice bottles looked milky next to PET. Clarifiers change that. Additives in the Millad 3988 family from Milliken reduce crystal size so light passes through instead of scattering, and a clarified PP bottle reads as clear on a shelf. It is still not PET: expect a faint warm cast and a softer surface, and check haze on a real bottle rather than a resin data sheet.
If the juice must look like water, apple or white grape, PET remains the reference, and no clarifier closes the gap completely. With orange, mango or tomato, the difference largely disappears: color does the visual work, and PP brings a squeezable, drop-resistant bottle. The trade is usually acceptable for tinted juice and usually not for a water-clear one.
Clarity also depends on mold surface and cooling, so thePET and PETG comparisonis a useful companion; thesingle-station 0.1–16 L rangecovers the models used for juice sizes.
Heat resistance: why 98°C changes the machine choice
Hot fill turns the material question into an equipment question. PP softens at a higher temperature than PET, so a PP bottle can take a fill near 98°C, the figure used in the published Tampico case, without collapsing. Standard PET has no such margin. Hot-fill PET relies on heat-set mold temperatures and a controlled cooling profile, and even then the process window is narrower.
PP is not automatically a hot-fill answer either. Heat still reaches the neck, handle and base, and the bottle must cool inside tolerance. Fill temperature, hold time, cooling tunnel and conveyor speed belong in one test.
- Fill temperature and hold time at the filler head, not the label claim.
- Shrink and neck ovality measured after cooling.
- Closure and liner rated for the same temperature.
- Vacuum panel or controlled deformation, if the product cools in pack.
- Wall thickness at the base and pinch-off, where hot fill finds weak points.
Output: extrusion blow molding vs stretch blow molding
The routes form the bottle differently, so a raw cycle comparison misleads. PP here is extrusion blow molded: a parison is extruded, clamped, blown and taken off. PET juice bottles are injection stretch blow molded: a preform is molded first, then reheated, stretched and blown. Each route has its own bottleneck, and the bottleneck sets output.
| Decision point | Clarified PP, extrusion blow molding | PET, injection stretch blow molding |
|---|---|---|
| Clarity | Clear with a faint warm cast; haze depends on clarifier, mold finish and cooling | Glass-like; the reference for water-clear juice |
| Hot fill | Cited up to about 98°C in the 2005 Tampico case | Needs heat-set tooling and a narrower cooling window |
| How the bottle is made | Parison extruded, clamped, blown, taken off | Preform molded, reheated, stretched, blown |
| Output ceiling | Cavities × good parts per cycle; extruder plasticizing capacity is the ceiling | Preform cavitation and the blow cycle set the pace |
| Tooling | Blow mold and take-off | Preform mold plus blow mold |
| Resin handling | PP usually needs no drying before extrusion | PET preform resin is dried before molding |
| Best fit | Tinted juice, hot fill, squeezable bottles | Cold fill, crystal-clear juice, short shelf life |
Swipe the table to see all columns →
Output math is the same on both routes: cavities × good parts per cavity per cycle × cycles per hour, where cycles per hour = 3600 ÷ measured cycle time. On an extrusion blow molding machine the extruder's plasticizing capacity is the real ceiling, so cavities beyond what the screw can feed buy scrap, not output.
What the Tampico case shows, and what it does not
The case usually cited for PP juice bottles dates from 2005 and involves the juice brand Tampico, the clarifier supplier Milliken with its Millad 3988 grade, and the resin producer Braskem. Clarified PP bottles were hot filled at up to about 98°C, and the switch was reported to run roughly 30% higher output than the PET line it replaced. That figure is a case result, not a machine specification.
It does not give a cycle time for a different mold, cavitation or extruder, and it says nothing about E-SHION machines. Treat it as evidence that the combination works, not as a benchmark. A PP trial on the proposed screw and temperature-control configuration is the only way to get your own number.
If the volume justifies two stations, thedouble-station 0.1–16 L rangeis the alternative, andmachine reference checkslists what to verify before shipment. To have the configuration calculated for your bottle,send the drawing and fill data.
What to send for a quotation
A usable quotation needs the bottle and the line, not just a volume.
- Bottle drawing or 3D file: volume, weight, neck finish and handle position.
- Material: PP grade and clarifier, or the PET preform spec you are comparing against.
- Fill temperature, hold time and cooling method, the most important input of all.
- Product details: pulp, preservative, pH, and whether the line hot fills or cold fills.
- Target output per shift or per year, and the cavitation you expect.
- Existing mold or sample bottle, if there is one.
- Plant utilities: voltage, frequency, compressed air and chilled water.
- Destination port and required delivery window.
Source: E-SHION product data. Specifications are subject to change without notice; customization is available.
This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.