A hot-fill project rarely fails at the extruder. It fails at the drawing stage, when a container designed for ambient filling runs at 85 °C and the body panels pull in, the base deforms, or the cap will not seat once the bottle has cooled. Resin, wall section and mold cooling have to be chosen against the fill temperature before anything is quoted.
Three numbers decide the resin, not the container volume
Fill temperature, hold time and the top-load the container must carry after cooling are the three inputs that matter. Short contact below roughly 80 °C usually stays with HDPE. Sustained filling at 85 °C and above usually moves to PP. Confirm the grade with the resin supplier before the drawing is frozen.
Container volume only tells you which platform to look at. A 5 L pack and a 30 L drum sit on machines with different clamp forces and daylight. Heat is a separate question, and the answer comes from the filling line, not from the machine series.
Where HDPE stops and PP starts
The usual split is easy to state and easy to get wrong once a real product is on the line.
- HDPE: ambient to warm fill, with short contact below roughly 80 °C. It remains the default for detergents, lubricants, agrochemicals and household chemicals where the product does not sit hot in the container.
- PP: sustained filling at 85 °C and above, where the container has to hold its shape while hot. Grade, shrinkage and impact requirements are a conversation with the resin supplier, not a machine setting.
- Barrier layers: EVOH multi-layer configurations are available where the product needs an oxygen barrier, but the layer structure is project-specific. Confirm what the series you are considering can run.
- Beyond the standard range: heat-set or higher-temperature filling is a joint decision by the resin supplier, the filler and the machine builder. Treat it as a trial, not a table lookup.
Two cautions before the table. First, hot fill is used loosely as a term: a 65 °C sauce and an 88 °C juice are different problems. Second, hold time matters as much as temperature, because a container that touches 85 °C for a moment is not the same as one that holds it through a long cooling tunnel.
Fill temperature, resin and the design response
| Fill temperature / hold time | Resin direction | Container and panel design | Mold and cooling change |
|---|---|---|---|
| Ambient to about 60 °C, no hold | HDPE; PP only where the product requires it | Standard bottle, no vacuum panels | Baseline mold temperature and cooling |
| About 60–80 °C, short contact | HDPE usually workable; grade to be confirmed | Shallow panels or an ovalised body to absorb pull-in | Slightly longer cooling; check the shrinkage allowance |
| 85 °C and above, sustained | PP is the usual direction | Vacuum panels, reinforcing ribs, thicker base | Higher mold temperature, longer cooling, ejector and take-off review |
| Beyond the standard range / heat-set | Specialty grade recommended by the resin supplier | Drawing reviewed together with the filler | Confirm by trial; do not read this table as a specification |
Swipe the table to see all columns →
Read the bands as a starting point for the RFQ, not as a specification. The numbers that matter are the ones your filling line actually runs, and they should come from a temperature log rather than a product data sheet.
What hot fill changes in the mold and the line
Hot fill does not stop at the resin. A container filled hot shrinks as it cools, so the mold has to allow for shrinkage in height, diameter and neck. Vacuum panels give the body somewhere to collapse in a controlled way instead of distorting the label area or the base. Both changes affect cooling time, because a paneled body with uneven wall sections holds heat longer than a plain cylinder.
Ejection and take-off move as well. A warm, softer container needs support at the base and at the neck when it leaves the mold, and a take-off setting that suits an ambient-fill bottle can mark the body or ovalise the neck. Review the handling chain with the mold, not after it.
A decision path you can run before the RFQ
Walk one container through four questions in order, and stop at the first one you cannot answer. That is usually where the project is still open.
- What is the real fill temperature at the nozzle, and how long does the product stay hot inside the container?
- What top-load must the container carry after cooling: in the pallet, in the warehouse, and at the capping head?
- Is the bottle shape fixed by the brand, or open? A shape with large flat panels may have nowhere to absorb the vacuum.
- What cooling tunnel or cooling method is used, and how quickly does the container reach a temperature where it can be handled?
If the answers point to a 20–50 L container, the ES-30L (215 kN clamp, 580 × 740 mm platen, 350–800 mm daylight) and the ES-50L (260 kN, 880 × 780 mm platen, 400–1000 mm daylight) cover the taller molds that hot-fill work often needs. Small PP packs usually start on the 0.1–16 L double-station platform, where the ES-10LD offers 110 kN clamp and 220–600 mm daylight.
Compare thedouble-station 0–16 Landsingle-station 0–16 Lplatforms, or readHDPE bottle blow moldingfor the ambient-fill side. If the container is a clear PETG jar rather than a hot-fill pack, the annealing question is different — seePETG jar annealing.
What to send for a quotation
A hot-fill quotation is only as good as its inputs. Send these together and the model, cavity layout and cooling recommendations can be checked against real numbers instead of assumptions.
- Container drawing with neck finish, body panels and base, plus the top-load required after cooling.
- Fill temperature at the nozzle, hold time, and the cooling tunnel or cooling method.
- The resin grade you intend to run, or the product and its compatibility requirements if the grade is still open.
- Output target in good bottles per hour, cavity count if it is already fixed, and whether containers are palletised straight from the line.
- Destination, voltage and any line integration constraints such as take-off, conveyor or capper.
Send the drawing and the three numbers through thecontact pageand we will confirm what still needs to be decided before a mold is cut.
Source: E-SHION product data. Specifications are subject to change without notice; customization is available.
This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.