A brand owner asks for the carbon footprint of one bottle, and the first question back is usually about the machine. That is the smallest lever in the calculation. For a blow molded HDPE or PP bottle, cradle-to-gate emissions are decided mainly by how much resin the bottle holds and what that resin is made from. The line's electricity is a real line item, but a second-order one. Getting a defensible answer means separating four contributors and refusing to estimate any of them twice.
Set the boundary and the unit before any number
Use cradle-to-gate: resin production, bottle conversion electricity, scrap and regrind, and transport up to your factory gate. Report grams CO2e per 1,000 good bottles, because that is the unit a customer can scale to an order. State the source and year of every emission factor next to the result.
- Resin: bottle weight × bottles × resin factor, with the scrap allowance kept visible.
- Electricity: measured kWh on the line ÷ good bottles produced, using actual draw rather than installed power.
- Scrap and regrind: count the yield loss once; regrind that returns to the same parison is not a second resin input.
- Transport: inbound resin and outbound bottles to the gate, with mode and distance written down.
Resin is the line that decides the total
A 25 g bottle carries 25 kg of resin per 1,000 units; a 950 g container carries 950 kg. Multiply that mass by a resin factor taken from the supplier's EPD or a licensed LCA database and you have the largest single term in most blow molded bottle carbon footprints. This is why recycled content, bottle weight and wall design move a brand owner's total far more than swapping one blow molding machine for another. Machine choice changes the electricity line: worth measuring, but second order.
If you are comparing line layouts for small bottles, look at thesingle-station 0–16 L machinesand thedouble-station 0–16 L machines. Bottle weight and cavity count are usually fixed long before an LCA starts; the1–2 L small bottle production guideshows how those two numbers are set.
Electricity: measure actual kW, not the nameplate
Installed power is every motor, heater and drive at full load; a running line never sits there. Across the ten models in the 0–50 L range, measured draw runs from roughly 12–18 kW on the ES-2LS to roughly 35–50 kW on the ES-50L, against installed figures of 24–32 kW and 105–120 kW. Log a full shift, including heater cycling, clamp, blow and extruder, then divide by good bottles rather than scheduled bottles.
| Part weight | Resin per 1,000 good bottles | Machine class and power | Electricity line |
|---|---|---|---|
| 25 g | 25 kg before scrap | ES-2LS class: 12–18 kW actual, 24–32 kW installed | measured kW × 1,000 ÷ good bottles per hour |
| 160 g | 160 kg before scrap | ES-10LS class: 38–48 kW installed — log the actual draw | same formula, using measured cycle time |
| 950 g | 950 kg before scrap | ES-50L class: 35–50 kW actual, 105–120 kW installed | same formula; add chiller and compressor only if they sit inside your boundary |
Swipe the table to see all columns →
The grid factor can matter as much as the kWh. Take it from a published source — IEA grid emission factors, or your national inventory — and record the source, the region and the year. A factor from 2019 and a factor from 2024 can move the result enough to start an argument with a customer, so print the year beside the number.
Scrap, regrind and transport: keep the lines separate
Scrap is where double counting happens. A bottle that is ground and fed back into the same parison never leaves the plant as waste, but its resin was already counted. Keep the regrind loop on its own line: yield loss on the resin side, plus the grinder's kWh on the electricity side. Do not add the regrind mass a second time. Transport then covers resin coming in and bottles going out to the gate, with mode and distance stated, not assumed.
How the four lines add up for a 160 g bottle
One thousand 160 g bottles hold 160 kg of resin in the product alone. If your measured scrap rate is 3%, the resin actually purchased is about 165 kg, and the extra 5 kg belongs on the scrap line. Electricity is the logged kWh per 1,000 good bottles multiplied by the grid factor for the plant's region and year. Transport to the gate is the fourth line. What comes out is one g CO2e figure with a written trail behind it.
Run the same sheet at 25 g and 950 g and the pattern holds: the resin line scales with part weight, the electricity line scales with time on the machine, and only the resin choice changes both the size and the origin of the biggest term.
What to send for a quotation
To price a line you can actually measure, send these:
- Bottle drawing or sample, with weight in grams and the resin grade.
- Target output in pieces per hour, and the shift pattern.
- Cavity count you want to test, and whether multi-layer or recycled content is in scope.
- The carbon footprint method your customer requires: boundary, factor sources and the unit they report in.
- Factory destination, because the quotation and the power supply both depend on it.
With those five items we can match a model, state the installed power and agree on which readings to record at the test. The footprint itself stays yours to publish — but the kWh behind it will be measured, not assumed.
Source: E-SHION product data. Specifications are subject to change without notice; customization is available.
This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.