A wide-mouth PP jar looks simple on the drawing and becomes difficult at the second meeting. The resin supplier offers homopolymer, impact copolymer and random copolymer, with or without a nucleating agent, and each choice moves the shrinkage, the drop result and the warpage. The mold is already being quoted. Before anyone cuts steel, three decisions settle whether the first samples pass or come back oval, sunk or split at the pinch-off.
Homo, copolymer or random: the short answer
Use homopolymer when the jar must hold its shape under heat or stack load, and impact copolymer when it must survive a drop in cold weather. Random copolymer sits between them and is chosen for clarity and a softer feel, at some cost in stiffness. Then confirm shrinkage with the resin supplier.
That rule covers most jars but it is not a specification. The grade also fixes how much the part shrinks, how the base behaves under a stack, and whether the thread stays round after cooling. Two suppliers can both offer PP copolymer and still deliver different shrinkage and drop results, because comonomer content, MFI and the nucleator package differ.
What each grade does on a wide-mouth jar
Read the grade as a set of trade-offs, not a ranking. A jar stacked in a warehouse and a jar dropped from a pallet in winter want different resins, and the same drawing can be correct in two different grades.
- Homopolymer gives the highest stiffness and heat resistance of the three, which is what a stacked jar or a stiff neck and thread needs. Its weak point is low-temperature drop impact.
- Impact copolymer puts ethylene units in the chain to absorb impact energy, so the jar handles rough handling and cold drops better. Stiffness and heat resistance are lower than homopolymer.
- Random copolymer is chosen for clarity and a softer feel. It is less stiff, so check the wall and the stack load before committing.
- A nucleating agent raises stiffness and can shorten the cycle and improve clarity, but it also changes shrinkage and warpage. Mold dimensions and cooling have to be re-checked, not carried over.
- A clarifier is a separate additive aimed at transparency. Treat clarity as resin plus mold temperature plus cooling, and confirm it on a trial jar.
Shrinkage: the number that decides the mold
PP shrinks more than HDPE, and both homopolymer and copolymer do it. If the mold is cut to the dimensions of an HDPE jar, the PP jar will come out small, and the neck and the base will not correct each other. The mold maker needs a shrinkage value from the resin supplier, measured at the wall thickness and cooling you will actually run — not a generic figure from a table.
Ask two questions, not one. First: what is the shrinkage range at my body wall and my intended mold temperature? Second: which direction does it move if I switch base grade or add a nucleator? Give the mold maker the range and the direction, then confirm the final cavity dimensions against the drawing before the mold is cut.
For the machine side, see thesingle-station 0.1–16 L seriesand the HDPE comparison inHDPE bottle blow molding.
Grade comparison for blow molded jars
The table compares grades qualitatively, because the numbers belong on your resin data sheet. Use it to shortlist, then ask the supplier for values at your wall.
| Grade | Stiffness | Cold-drop impact | Heat resistance | Shrinkage | Watch-out |
|---|---|---|---|---|---|
| Homopolymer | High | Lower | Higher | Above HDPE; take the value at your wall | Stacked jars, stiff necks, heat |
| Impact copolymer | Medium | Higher | Medium | Above HDPE; grade-dependent | Cold-drop jars, handles, rough handling |
| Random copolymer | Lower | Medium | Lower | Grade-dependent; confirm before cutting | Clarity-led jars with a light load |
| Nucleated base grade | Raised vs. base | Follows base grade | Follows base grade | Changes vs. base grade; re-check warpage | Stiffness or cycle gain, after a trial |
Swipe the table to see all columns →
Reading a defect back to the grade
Most PP jar defects are blamed on the machine when the grade set the trap. Work backwards from the defect before touching clamp force or cycle time.
- Warpage across the base or an oval neck: check grade shrinkage first, then cooling balance and mold temperature. A nucleated grade can move warpage even when the wall is unchanged.
- Sink on a thick section or under a rib: a softer copolymer sinks more at the same wall, so check wall design and cooling before adding clamp force.
- Stress whitening at the pinch-off or thread: often impact copolymer being over-strained, or a cold mold. Check clamp force against mold projection area and blowing pressure, not container volume alone.
- A split in a cold drop test: homopolymer at low temperature. Consider an impact copolymer, or accept a heavier wall.
- Bubbles or holes: usually moisture or contamination, not the grade. Dry the resin and check the regrind before changing anything else.
If regrind is part of the recipe, the ratio limits are covered inblow molding regrind ratio.
Whenever the grade changes, plan a short trial: measured cycle time, wall-thickness sections at four points, a drop at the lowest temperature the jar will meet, and a stack test. Record the grade and the MFI condition next to the results, or the numbers cannot be compared later.
What to send for a quotation
A usable quotation starts from the jar and the resin, not from the volume alone. Send these and the machine, mold and cycle discussion becomes specific.
- Jar drawing: volume, overall height and diameter, wall at body, base and neck, thread spec and neck finish.
- Resin: homopolymer, impact copolymer or random; nucleator or clarifier; MFI with its test condition; shrinkage range at your production wall.
- Food-contact or migration requirement the jar must meet.
- Cavity count, target output per hour and, if the part already runs, the measured cycle time.
- Mold status: new or existing, cavity layout, take-off method, and whether the neck needs finishing.
- Site utilities and destination: power, compressed air, chilled water, and the port.
Cavity count decides the platform: compare thesingle-station 0.1–16 L serieswith thedouble-station 0.1–16 L series, and send the drawing throughcontact.
Final price depends on model, mold, cavity layout, material, drive and control, and destination. As a market frame only, 5–30 L extrusion blow molding machines are commonly quoted at USD 40,000–90,000; confirm your configuration in the quotation.
Source: E-SHION product data. Specifications are subject to change without notice; customization is available.
This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.