A specification sheet is not a ranking. Two machines can both say 30 L and 215 kN and still behave differently once your mold is on the platen. Most first-time buyers compare container size and price, then discover that the platen is too small for a two-cavity tool, or that the quoted output assumed a cycle their wall thickness will never reach. The numbers that decide the project are on the sheet — just not the ones people read first.

Start from the mold, not the model number

Read the sheet outward from your mold. Clamp force must cover the mold's projected area multiplied by blowing pressure. Platen width and height must accept the mold body, clamps and water fittings. Screw diameter and drive set the plasticizing ceiling. Container volume only tells you which series to open; the rest is a fit check against a real drawing.

Every line belongs to one of three groups. Fit numbers — clamp force, platen size, mold height — decide whether the tool runs at all. Rate numbers — screw, output, cycle — decide how many good parts you get per hour. Utility numbers — installed power, air, water — decide what the plant must supply. Mixing the groups is how buyers compare a small machine's output with a large machine's clamp force and learn nothing.

If your container is under 16 L, compare thesingle-station 0–16 L rangewith thedouble-station 0–16 L rangebefore comparing price. The second station changes output and floor space; it does not change the mold-fit rules above.

Line by line: what each number actually decides

Use the sheet as a checklist against the mold drawing and the production plan, not as a scorecard between brands.

  • Clamp force (kN): holds the mold closed. Compare it with projected area × blowing pressure for your largest cavity layout, not with container volume.
  • Platen width × height (mm): the usable mounting face. Check the mold plate, clamp slots, neck insert and water fittings.
  • Screw diameter (mm): with L/D, screw design and drive, it sets melt delivery per hour. A bigger screw is not automatically a better match.
  • Output (kg/h): a melt-rate reference. Convert it with part weight, cavities and measured cycle before trusting a parts-per-hour figure.
  • Installed power (kW): what the supply must carry, not the running consumption, which depends on cycle and heat-up.
  • Cavity count and layers: what the head was built for. Adding cavities or a barrier layer later is a new head and tool decision.

Some numbers never appear on a summary sheet: mold height range, opening stroke, dry-cycle time, tie-bar spacing and the exact platen slot pattern. Ask for the machine drawing and compare it with the mold drawing before you sign. If a supplier will not send a drawing, treat the summary as marketing.

Four models, one table

The table decodes the published reference values for four models in the 10–50 L band. Read down a column to see what one machine offers; read across a row to see what a change buys.

Published reference values for 10–50 L single-station models — confirm final values in the quotation
Spec line ES-10LS ES-16LS ES-30L ES-50L What it decides
Clamp force110 kN155 kN215 kN260 kNWhether the mold stays closed against blowing pressure
Platen (W × H)450 × 480 mm500 × 490 mm580 × 740 mm880 × 780 mmWhether the mold body and clamps fit
Screw diameter70–75 mm75 mm80 mm90 mmMelt delivery per hour
Output80–100 kg/h100–120 kg/h100–120 kg/h110–160 kg/hPlasticizing ceiling for your cycle
Installed power38–48 kW48–55 kW100–110 kW105–120 kWTransformer and cable sizing

Swipe the table to see all columns →

Two jumps stand out. ES-16LS to ES-30L nearly doubles installed power and widens the platen from 500 to 580 mm, because the clamp and frame are built for a heavier tool and a larger parison. ES-30L to ES-50L adds 45 kN of clamp but only a modest step in output: the 50 L body needs platen area and the 90 mm screw more than raw tonnage. Read this way, the sheet shows where the cost sits.

30L Container Blow Molding Machine | Mold and Container View A representative 30l container blow molding machine | mold and container view clip. The machine, mold and configuration in your project may differ.

The three numbers buyers misread

First, clamp force. It is a mold-fit number, not a size class. A 30 L container with a large flat panel and high blowing pressure can demand more clamping than a taller, narrower 50 L body. Check projected area on the drawing.

Second, output in kg/h. Take ES-30L at 100–120 kg/h. A 0.85 kg container on a 55-second measured cycle gives about 65 parts an hour from one cavity, or 55 kg. Two cavities at the same cycle give about 131 parts, or 111 kg — inside the range but at its top, so any cycle slip shows immediately. Stretch the cycle to 62 seconds and the same two cavities fall to about 99 kg/h. The sheet did not change; the cycle did.

Third, installed power. It sizes the supply, not the bill. A machine rated 100–110 kW installed does not draw that continuously; heat-up, idle and running phases differ, and the actual figure depends on your cycle and heater settings. Ask for the connected load and the recommended breaker, then let an electrician size the cable.

What to send for a quotation

A quotation is only as good as the inputs. Send these six items and the reply can be specific instead of a price range.

  • Container drawing with capacity, neck finish, weight and wall-thickness target.
  • Cavity layout you want, and whether it must grow later.
  • Material and layer structure, including any regrind share.
  • Target output in good parts per hour and the shift pattern.
  • Mold drawing, or mold weight and dimensions if the tool already exists.
  • Destination country, supply voltage and available air and water.

If the mold does not exist yet, send the container drawing and we will work backward to the machine and the tool. Either way, ask for the machine drawing with the quotation — the fit check should be visible on paper before any deposit.

For the mechanical background, readhow a blow molding machine is builtandwhat an OEM contract manufacturing project involves. Send drawings through thecontact page.

Source: E-SHION product data. Specifications are subject to change without notice; customization is available.

This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.