A bubble in a blow molded bottle looks the same whether it came from wet resin, a folded parison or a hot spot in one cavity, and each of those has a different cure. Rejecting the lot, drying harder or dropping the temperature before you know which one you are looking at usually adds a second problem to the first. The pattern of the bubbles, not the bubble itself, is the evidence you can act on.

The short answer: distribution points to the cause

Bubbles spread evenly across all cavities point to the material: moisture, contaminated regrind or an overheated melt. Bubbles fixed to one cavity, one clock position or one thick section point to trapped air or a local hot spot, such as a parison fold at the seam, a blocked vent or cooling that lags in that spot.

This split matters because the fixes sit in different places. Material problems are solved upstream: resin lot, regrind ratio, drying, melt temperature and residence time. Spot problems are solved at the mold: venting, parison length, pre-blow timing, blow-pin condition and cooling around that section. Using a downstream setting to fix an upstream problem is how a one-day defect becomes a two-week trial.

The bubble signature table

Use the table as a first sort, not a diagnosis. Match the signature on the bottle, then confirm it with the cut section described below. When two rows fit, the cut usually decides between them.

Bubble and void signatures in extrusion blow molded containers
Signature Where it appears Most likely cause First check
Fine closed bubbles, even sizeAll cavities, all wall positionsMoisture or volatiles in the resin; dusty or damp regrindResin lot, regrind ratio, supplier dryness data
Large void at the pinch-offSeam area, one or both sidesParison folded, or air trapped at mold closeParison length, pre-blow timing, seam vent
Dark-rimmed void in a thick sectionHandle, neck ring, boss, threadOverheated melt or degradation; slow cooling in thick wallMelt temperature, residence time, cooling at that section
Bubbles at one clock positionSame spot on one cavity onlyCavity hot spot, blocked vent or leaking blow pinSwap the mold between stations; check vent and blow pin
Bubbles after a regrind increaseRandom, all cavitiesRegrind fines, moisture pickup, inconsistent flake sizeRegrind ratio and flake quality
Elongated voids along the wallDownstream of the die, thin wallAir drawn in at the die, or a parison that sags and foldsDie gap, parison speed and support

Swipe the table to see all columns →

One row deserves a warning. A void in a thick section is often not a gas bubble at all but a shrinkage void: the wall pulls apart as it cools because the outside froze before the inside. It looks like a bubble in a cut and no amount of drying removes it. Check whether the cavity has smooth, drawn-out walls and sits in the thickest part of the part.

Machines used for this container size are described undersingle-station 0–16 Landdouble-station 0–16 L. If bubbles appear on one station only, suspect the mold or that station's blow circuit before the resin.

Cut a section: three cuts that separate air from moisture

A cut section costs one bottle and ten minutes and removes most of the guesswork. Cut with a sharp blade or a band saw, wet the surface slightly, and look at it in side light. A phone photo taken at an angle shows more of the cavity shape than a straight-on shot.

  • Across the bubble. A closed cell with a smooth inner wall formed while the resin was molten, so the gas came out of the melt. A ragged tunnel that reaches the surface was air that never escaped.
  • Along the wall through the seam. A fold line beside the void means the parison closed on itself and the air had nowhere to go.
  • Through the thickest section. A smooth, drawn-out cavity with no dark rim is usually shrinkage, not gas.
5L Jerrycan Blow Molding Machine | Mold Close-Up A representative 5l jerrycan blow molding machine | mold close-up clip. The machine, mold and configuration in your project may differ.

If you cannot cut a sample yet, watch the parison before the mold closes. A parison that swings, touches the mold face or folds before pre-blow will trap air, and that is a timing and alignment question rather than a resin question. It also repeats in the same place every cycle, which is the signature to look for.

When the cause is the resin, not the machine

If bubbles are spread across every cavity, work upstream in this order: resin lot, regrind, drying, melt temperature, residence time. A new lot can arrive wetter than the last. Regrind carries dust, absorbs moisture and can be dry on the outside of a flake while wet inside. Neither problem announces itself; the bottle does.

Ask the resin supplier for dryness data for the lot and the recommended drying window for the grade, then confirm the dryer actually reaches it. Inlet temperature, dew point, hopper residence time and airflow all matter, and a dryer that is switched on is not the same as a dryer that is working. Do not copy a drying temperature from another grade or from a forum; that number belongs to the resin data sheet.

A worked example: bubbles in one cavity of four

A four-cavity 5 L HDPE jerrycan line reports bubbles in cavity 3 at the same height on the bottle, every cycle. Cavities 1, 2 and 4 are clean. The resin lot has not changed and the dryer runs the same schedule, so material is the weaker hypothesis. The operator swaps the mold halves between stations: if the bubbles follow the mold half, the cavity is at fault; if they stay on station 3, the station is.

Suppose they follow the mold half. Next checks are the vent at that clock position, the cooling channel in that insert and the blow pin on that station. A vent blocked by flash and a cooling channel with scale both create a local hot spot, and a hot spot creates gas from the melt in exactly one place. Neither shows up on a resin certificate.

If the pattern ends up at the mold or the blow circuit, reviewwhat the machine warranty coversandhow after-sales service is handledbefore you book a visit.

What to send for a quotation

Send the samples below rather than a description. A marked reject tells us where, a good bottle tells us what the target is, and a cut section tells us what is inside the wall. With those three we can quote a machine, a mold change or a drying setup against your actual defect.

  • One reject with the bubble untouched, marked with cavity number and clock position.
  • One good bottle from the same shift, for comparison.
  • One cut section through the bubble, photographed in side light.
  • Resin grade, lot number and regrind ratio.
  • Melt temperature, cycle time and drying settings as actually run.
  • Machine model, cavity count and mold drawing if available.

Send the photos and data through thecontact pagewith the cavity number and resin grade in the subject line; it saves a round of questions.

Source: E-SHION product data. Specifications are subject to change without notice; customization is available.

This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.