The air compressor is usually the last item on the utility list and the first one that stops a new blow molding line from holding pressure. The machine is rated for 0.8 MPa, the plant already has a compressor, and everyone assumes the two will match. They often do not. The machine's figure is blow air at the machine inlet, measured while the clamp, the blow pin and the parison handling are working. The compressor's figure is free air delivery at some other pressure, quoted before the dryer, the filters and the pipe take their share. The gap between them appears later as wall-thickness variation, weak pinch-off and a cycle that never quite repeats.

What Air Pressure and Flow Does a Blow Molding Machine Need?

Across the E-SHION range, published blow-air demand is 0.6–0.8 MPa and 0.6–1.5 m³/min. Smaller single-station models such as the ES-2LS and ES-5LS run at 0.6 MPa and 0.6–1 m³/min; the 10 L and 16 L models, and the 30 L and 50 L machines, specify 0.8 MPa. 0.8 MPa is 8 bar. Double-station models sit at the top of the flow range.

Read that as a demand figure for one machine, not as a compressor datasheet. The pressure is blow air — the air that inflates the parison inside the mold — and it is separate from clamp force, which is quoted in kN: 100 kN on the small models, 110 kN on the 10 L models, 155 kN on the 16 L models, 215 kN on the ES-30L and 260 kN on the ES-50L. The two interact. Clamp force has to be checked against mold projection area and blowing pressure, so a plant that raises blow pressure to chase a wall-thickness problem is also raising the force the clamp must hold.

Published Air Data by Model

Published blow-air pressure and consumption for the 0.1–16 L and 20–50 L ranges. Confirm against the final machine drawing and your mold.
Model Container size Blow air pressure Air consumption
ES-2LS2 L0.6 MPa (6 bar)0.6–1.0 m³/min
ES-5LS5 L0.6 MPa (6 bar)0.6–1.0 m³/min
ES-10LS10 L0.8 MPa (8 bar)0.8–1.0 m³/min
ES-16LS16 L0.8 MPa (8 bar)0.8–1.0 m³/min
ES-2LD2 L0.6 MPa (6 bar)1.0–1.5 m³/min
ES-5LD5 L0.6 MPa (6 bar)1.0–1.5 m³/min
ES-10LD10 L0.8 MPa (8 bar)1.0–1.5 m³/min
ES-16LD16 L0.8 MPa (8 bar)1.0–1.5 m³/min
ES-30L30 L0.8 MPa (8 bar)0.8–1.0 m³/min
ES-50L50 L0.8 MPa (8 bar)0.8–1.0 m³/min

Swipe the table to see all columns →

Values are per machine at the machine inlet, with the mold you intend to run. Two patterns matter. Double-station models consume more air than the single-station model at the same container size — the ES-5LD is listed at 1–1.5 m³/min against 0.6–1 m³/min for the ES-5LS — because two molds blow in the same cycle. And the 30 L and 50 L machines hold 0.8 MPa at 0.8–1.0 m³/min, the same band as a 16 L single-station machine: blow air is not what grows with container size; the clamp and the extruder are.

5L Plastic Bottle Blow Molding Machine | Mold and Take-Off A representative 5L plastic bottle blow molding machine | mold and take-off clip. The machine, mold and configuration in your project may differ.

Sizing the Compressor: FAD, Receiver, Dryer and Pressure Drop

A compressor is sold by free air delivery at a stated pressure, which is where most sizing mistakes start. A unit rated 1.5 m³/min at 7 bar does not deliver 1.5 m³/min at 8 bar; for the same machine, higher discharge pressure means lower delivered flow. Compare the compressor's FAD at the pressure your machine uses — 0.8 MPa for the 10 L and 16 L models, the 30 L and 50 L machines and the ES-10LD and ES-16LD; 0.6 MPa for the smaller models — and ask for the figure at that pressure.

The dryer and the filters sit between the compressor and the machine and each costs pressure. A refrigerated dryer running above its rated inlet temperature, an undersized coalescing filter or a spent element all show up as a lower gauge reading at the machine. The receiver does a different job: it buffers the blow surge so the header does not dip every cycle. A receiver too small for the cavity count and the cycle overlap produces a pressure wave that tracks the cycle, and a pressure wave at the blow pin produces a wall that varies around the bottle.

  • Compressor FAD quoted at the machine's working pressure, not at a lower one.
  • Receiver sized for the blow surge at the cavity count you are buying, not the one you run today.
  • Dryer and filters rated for full flow at your ambient and inlet temperature.
  • Header and drops sized for velocity, with a gauge at the machine inlet.
  • A leak survey before commissioning — a leaky plant hides behind an oversized compressor.

If the model is still open, start from thesingle-station 0–16 L rangeor thedouble-station 0–16 L range, then check the clamp side againstclamping force and mold projection area. Utility details can go with the inquiry on thecontact page.

A Sizing Check You Can Run Before the Machine Arrives

Take a plant adding a second ES-10LD. The published figure for one machine is 1.0–1.5 m³/min at 0.8 MPa. Two machines at the top of that range are 3.0 m³/min of blow air at 8 bar, before any allowance for leaks, dryer purge or the next machine. If the compressor on the floor is quoted at 3.0 m³/min FAD at 7 bar, the number looks right and is not: at 8 bar the same unit delivers less, and the dryer and filters take more before the air reaches the blow pin. The check is arithmetic — demand at pressure, supply at the same pressure, and the supply has to be larger.

Then confirm it with a gauge. Run a full production cycle and read the inlet pressure at the moment the blow pin fires. If it falls below the machine's stated pressure, the compressor, receiver or header is short, and no adjustment at the machine will fix it. This is also the test when an existing compressor is being reused: a unit that holds pressure on one machine may not hold it on a double-station model with two molds blowing in the same cycle.

What to Send for a Quotation

Air supply is quoted with the machine only when the buyer asks, so put the utility data in the inquiry rather than adding it after the machine choice.

  • Container: volume, neck finish, wall-thickness target and material.
  • Model or range under consideration, and the cavity count.
  • Existing compressor: FAD, rated pressure, receiver volume, dryer type.
  • Measured pressure at the machine position during a production cycle, if a machine already runs.
  • Plant ambient conditions and the pipe run from compressor to machine.
  • Whether compressor, receiver, dryer and filters are in scope or bought locally.

With those, the reply can state the machine's air demand at the inlet and the supply needed behind it. That is a shorter conversation than the one that starts after installation, when the walls are thin and the compressor is blamed first.

Source: E-SHION product data. Specifications are subject to change without notice; customization is available.

This guide is written for production and procurement decisions. It uses published figures where available and avoids unverified performance claims.